manualshive.com logo in svg

GE ReadyToProcess WAVE 25, Operating Instructions Manual

Share
Download
GE ReadyToProcess WAVE 25 Operating Instructions Manual Download Page 53

Description

Component

Part

Connector for pH sensor fiber cable.

pH port

1

Gas outlet for connection to Cellbag bioreactor.

GAS MIX OUT

2

Indicates the CBCU operating status.

Status LED

3

Connector for DO sensor fiber cable.

DO port

4

Status LED

The status LED indicates the CBCU operating status according to the following table.

Description

Light indicator

The CBCU is ready for operation.

Steady green light

The CBCU is operating.

Green flashing light

Indicates an internal error, but the CBCU is still operating.

Red flashing light

Indicates an internal error, and the CBCU is not operating.

Steady red light

Rear view of ReadyToProcess
CBCU

The illustration below shows the rear panel of a fully configured CBCU.

1

2 3

6

5

4

ReadyToProcess WAVE 25 Operating Instructions 29009597 AD

53

3 System description

3.3 ReadyToProcess CBCU

Summary of Contents for ReadyToProcess WAVE 25













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands