GE PCIE-5565PIORC* Hardware Reference Manual Download

Page: 40 / 70

40 PCIE-5565PIORC Reflective Memory Board

4:3

Phantom Functions
Supported

Not Supported. Hardwired to 00

2:0

Max Payload Size
Supported

Max payload is 256 bytes
001

Table 3-30 Device Control Register Bit Definition

Device Control Register Bit Definition: Offset 0x088

Bit(s)

Field

Description

R/W

Reserved

14:12

Max Read Request

This card will only generate a max read
request of 128 bytes, but this register may
be written to any of the following.
- 000 = 128 Byte
- 001 = 256 Byte
- 010 = 512 Byte
- 011 = 1K Byte
-100 = 2K Byte
-101 = 4K Byte

R/W

Enable No Snoop

1 = Enable
0 = Disable

R/W

Aux Power PM Enable Not Supported. Hardwired to 0

Phantom Functions
Enable

Not Supported. Hardwired to 0

Extended Tag Field
Enable

Not Supported. Hardwired to 0

7:5

Max payload Size

000 = 128 Byte
001 = 256 Byte

R/W

Enable Relaxed
Ordering

1 = Enable
0 = Disable

R/W

Unsupported Request
Reporting Enable

1 = Enable
0 = Disable

R/W

Fatal Error Reporting
Enable

1 = Enable
0 = Disable

R/W

Non-Fatal Error
Reporting Enable

1 = Enable
0 = Disable

R/W

Correctable Error
Reporting Enable

1 = Enable
0 = Disable

R/W

Table 3-29 Device Capabilities Register Bit Definition (Continued)

Device Capabilities Register Bit Definition: Offset 0x084

Summary of Contents for PCIE-5565PIORC*







































































Search results

Summary of Contents for PCIE-5565PIORC*

Reviews:

Related manuals for PCIE-5565PIORC*

Brands by name

Popular brands

GE PCIE-5565PIORC*, Hardware Reference Manual

Search results

Summary of Contents for PCIE-5565PIORC*

Reviews:

Related manuals for PCIE-5565PIORC*

Brands by name

Popular brands