manualshive.com logo in svg

GE PanaFlow HT, User Manual

Share
Download
GE PanaFlow HT User Manual Download Page 24

Chapter 2. Installation

14

PanaFlow HT User’s Manual

2.5.3 Wiring Digital Outputs

Wiring any option set requires completion of the following general steps:

1.

Disconnect the main power to the unit and remove the wiring cover.

2.

Install the required cable clamp in the chosen conduit hole on the side of the electronics enclosure.

3.

Refer to Figure 10 on page 11 for the location of the terminal block and wire the digital output (C and D) as shown. 
Secure the cable clamp.

!ATTENTION EUROPEAN CUSTOMERS!

To meet CE Mark requirements, all cables must be installed as described in

Appendix G, 

CE Mark Compliance

.

4.

If wiring of the unit has been completed, reinstall the wiring cover on the enclosure and tighten the set screw.

Note:

Prior to use, the option must be set up and calibrated.

For more specific instructions on output configuration, proceed to the appropriate sub-section(s) that follow.

Note:

Digital Outputs can be configured as a totalizer pulse, frequency, alarms or control output.

Summary of Contents for PanaFlow HT




































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands