manualshive.com logo in svg

GE PanaFlow HT, User Manual

Share
Download
GE PanaFlow HT User Manual Download Page 16

Chapter 2. Installation

6

PanaFlow HT User’s Manual

2.2 Unpacking

Before removing the PanaFlow HT system from the crate, please inspect the flowmeter. Each instrument manufactured 
by GE Measurement & Control is warranted to be free from defects in material and workmanship. Before discarding 
any of the packing materials, account for all components and documentation listed on the packing slip. The discarding 
of an important item along with the packing materials is all too common. If anything is missing or damaged, contact 
GE Customer Care immediately for assistance.

Please note that your PanaFlow HT system may come in one of the three common configurations as shown below or a 
custom design system. Also, the electronics may be in a separate box from the meter body for a remote mount 
configuration.

Figure 3: PanaFlow HT Configurations

2.2.1 Identification

The PanaFlow HT meter has up to three separate labels for identification, depending on configuration. The system can 
be either mounted as a single unit (local mounting) or as two separate pieces (remote mounting).

2.2.1a XMT900 Transmitter Identification

Figure 4: XMT Transmitter Label (example)

Summary of Contents for PanaFlow HT




































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands