GE NetworX NX-7002 Installation Manual Download

Page: 14 / 39

LOCATION 1

DESTINATION SELECTION FOR REPORT CONTROL 1 (1 segment)

The NX-7002 contains up to six report controls. Each report control can be defined for SMS

reporting, TCP/IP reporting or email reporting (not yet available). This location contains the

report destination for report control 1. Select from the table below.

DATA

FORMAT

DESCRIPTION

Disabled

Report control 1 is disabled

TCP/IP 1

Reporting to TCP/IP receiver 1

TCP/IP 2

Reporting to TCP/IP receiver 2

Email 1

Email Reporting to Email Account 1 (not yet

available)

Email 2

Email Reporting to Email Account 2 (not yet

available)

SMS 1

SMS Reporting to Mobile Phone 1

SMS 2

SMS Reporting to Mobile Phone 2

LOCATION 2

BACKUP DESTINATION SELECTION FOR REPORT CONTROL 1 (1 segment)

If the primary destination selection (location 1) fails, a backup destination can be selected. If

using another device as the backup destination, for example, panel dialler, set the reporting

format (SIA or CID) in location 0, segment 2, option 1 and enable test report events for the

backup device. This location contains the backup report destination for report control 1. Select

from the table below.

DATA

FORMAT

DESCRIPTION

Disabled

Backup Report control 1 is disabled

TCP/IP 1

Backup Reporting to TCP/IP receiver 1

TCP/IP 2

Backup Reporting to TCP/IP receiver 2

Email 1

Backup Email Reporting to Email Account 1 (not yet

available)

Email 2

Backup Email Reporting to Email Account 2 (not yet

available)

SMS 1

Backup SMS Reporting to Mobile Phone 1

SMS 2

Backup SMS Reporting to Mobile Phone 2

255

Other dialler

The NX-7002 is not used as backup. Instead another

dialler is used (for example: panel dialler)

LOCATION 3

REPORT DELAY FOR REPORT CONTROL 1 (1 segment)

The delay in seconds before the NX-7002 GPRS module reports. If any other events occur

during this delay, they are sent with the first event in one message if using SMS reporting. This

does not apply if using TCP/IP reporting (it does not support multiple events in one message).

This can be from 0 to 255 seconds.

NX-7002 Installation manual

Page 14

09/02/05

Summary of Contents for NetworX NX-7002








































Search results

Summary of Contents for NetworX NX-7002

Reviews:

Related manuals for NetworX NX-7002

Brands by name

Popular brands

GE NetworX NX-7002, Installation Manual

Search results

Summary of Contents for NetworX NX-7002

Reviews:

Related manuals for NetworX NX-7002

Brands by name

Popular brands