GE Multilin G650, Manual

Page: 566 / 639

GEK-113285A G650 Generator Protection & Control System C-1
APPENDIX C C.1 DNP 3.0 PROTOCOL SETTINGS
C
APPENDIX C DNP 3.0 PROTOCOL FOR G650C.1DNP 3.0 PROTOCOL SETTINGS
G650 units enable the user to program certain parameters related to DNP3 protocol. These parameters are called DNP3
protocol settings and can be modified from the front panel or from the Level 2 software. The G650 relay supports
communication with multiple masters (3) and maintains three separate groups of DNP3 settings. Each group of DNP3
settings is related to a single
logical DNP3 slave device
. The G650 relay is able to communicate simultaneously with up to
three different DNP3 master stations. Each master communicates with a different
logical DNP3 slave
, these logical slaves
appearing as separate physical DNP3 slaves. This is achieved by keeping separate set of settings, event queues and set of
states for each logical device.
Notice that it is necessary to set different
DNP Address
and
TCP/UDP Port
for each
logical DNP3 slave device
.
Time synchronization through DNP protocol is available from all three DNP masters that can communicate with G650.
However the date & time will be taken from only one master at the same moment. It is recommended to use only one
master to do time sync through DNP.
SETTING NO SETTING NAME DEFAULT VALUE RANGE
1 Physical Port NONE NONE, COM1, COM2, NETWORK
2 Address 255 0 to 65534, step 1
3 IP Addr Client1 Oct1 0 0 to 255 step 1
4 IP Addr Client1 Oct2 0 0 to 255 step 1
5 IP Addr Client1 Oct3 0 0 to 255 step 1
6 IP Addr Client1 Oct4 0 0 to 255 step 1
7 IP Addr Client2 Oct1 0 0 to 255 step 1
8 IP Addr Client2 Oct2 0 0 to 255 step 1
9 IP Addr Client2 Oct3 0 0 to 255 step 1
10 IP Addr Client2 Oct4 0 0 to 255 step 1
11 IP Addr Client3 Oct1 0 0 to 255 step 1
12 IP Addr Client3 Oct2 0 0 to 255 step 1
13 IP Addr Client3 Oct3 0 0 to 255 step 1
14 IP Addr Client3 Oct4 0 0 to 255 step 1
15 IP Addr Client4 Oct1 0 0 to 255 step 1
16 IP Addr Client4 Oct2 0 0 to 255 step 1
17 IP Addr Client4 Oct3 0 0 to 255 step 1
18 IP Addr Client4 Oct4 0 0 to 255 step 1
19 IP Addr Client5 Oct1 0 0 to 255 step 1
20 IP Addr Client5 Oct2 0 0 to 255 step 1
21 IP Addr Client5 Oct3 0 0 to 255 step 1
22 IP Addr Client5 Oct4 0 0 to 255 step 1
23 TCP/UDP Port 20000 1 to 65535, step 1
24 Unsol Resp Function DISABLED DISABLED, ENABLED
25 Unsol Resp TimeOut 5 s 0 to 60 sec, step 1
26 Unsol Resp Max Ret 10 1 to 255, step 1
27 Unsol Resp Dest Adr 200 0 to 65519, step 1
28 Current Scale Factor 1 0.00001, 0.0001, 0.001, 0.01, 0.1, 1, 10, 100, 1000, 10000
29 Voltage Scale Factor 1 0.00001, 0.0001, 0.001, 0.01, 0.1, 1, 10, 100, 1000, 10000
30 Power Scale Factor 1 0.00001, 0.0001, 0.001, 0.01, 0.1, 1, 10, 100, 1000, 10000
31 Energy Scale Factor 1 0.00001, 0.0001, 0.001, 0.01, 0.1, 1, 10, 100, 1000, 10000
32 Other Scale Factor 1 0.00001, 0.0001, 0.001, 0.01, 0.1, 1, 10, 100, 1000, 10000
33 Current Deadband 30000 0 to 65535, step 1
34 Voltage Deadband 30000 0 to 65535, step 1
35 Power Deadband 30000 0 to 65535, step 1
36 Energy Deadband 30000 0 to 65535, step 1
37 Other Deadband 30000 0 to 65535, step 1
38 Msg Fragment Size 240 30 to 2048, step 1
39 Binary Input Block1 CTL EVENTS 1-16 See the explanation below