background image

Monogram.

ZISB480DM – GE Monogram 48" Built-In Refrigerator 

with Dispenser and Water Filter

47-1/2

7"

5"

Electrical
Area

84 1/2" max

83 1/2" min

Finished
Opening

74" From Floor

to Bottom

of Electrical

24"

5"

5"

3 1/2"

Water Supply

3 1/2"

48" Models 20"

THE INSTALLATION SPACE

*84" From
Floor to
Top Frame

48"

Frame to Frame

47"

Case Width

*83-1/2" 

at

Rear

*Shipping height. 

The refrigerator 
can be adjusted to 
fit into a cutout that 
is 83-1/2” min. to 
84-1/2” max. height.
Note that the top
case trim at the front
is 1/2” higher and 
will overlap upper
cabinetry or soffit.
Use leveling legs 
and wheels for 
height adjustment.

Specification Revised 8/02

20"

15"

23-7/8"
Behind
Frame

28-5/8"

130° Door Swing

90° Door Swing

Water And Electrical Locations 

The opening must be prepared with the electrical and water
supply located as shown.

The cutout depth must be 24".

Designed for industry standard flush installation. The refrigerator
will project forward, slightly beyond adjacent cabinetry,
depending on your installation.

The cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot exceed
the 24" installation depth shown. The top case trim overlaps
the bottom of the soffit.

Frameless cabinets:

The case trim overlaps cabinets at the top and sides.
Therefore, frameless cabinets may require filler strips to
prevent interference with cabinet door swing. The opening
must allow for filler strips.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is required. An

individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded 3-prong
electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.

Note

: GFI (ground fault interrupter) is not recommended.

• Water line can enter the opening through the floor or back wall.

The water line should be 1/4" O.D. copper tubing between 
the cold water line and water connection location, long
enough to extend to the front of the refrigerator. Installation
of an easily accessible shut off valve in the water line 
is recommended.

As an ENERGY STAR

®

 Partner, 

GE has determined that this product 

meets the ENERGY STAR

®

 

guidelines for energy efficiency.

Product Clearances

These refrigerators are equipped with a 2 position door stop.
The factory set 130° door swing can be adjusted to 90° if
clearance to adjacent cabinets or walls is restricted.

Allow minimum clearances for freezer door  and fresh food
door for a full 130° door swing and to allow for pan removal.

4" minimum clearance is required when door swing is adjusted
to 90°. If the 90° door stop position is used, pan access is
maintained, but pan removal is restricted.

For answers to your Monogram,

® 

GE Profile

or 

GE appliance questions, visit our website at
GEAppliances.com or call 
GE Answer Center

®

service, 800.626.2000.

R

Listed by
Underwriters
Laboratories

Summary of Contents for Monogram ZISB480DM







Reviews: