background image

For answers to your Monogram,

® 

GE Profile

 

or GE

®

 appliance questions, visit our website 

at ge.com or call GE Answer Center

®

 service,  

800.626.2000.

110111

Specification Created 3/08

Listed by 

Underwriters 

Laboratories

ZIS360NX

GE Monogram

® 

36" Built-In Side-by-Side Refrigerator with Automatic 

Icemaker and Water Filter

Dimensions and Installation Information (in inches) 

As an EnErgy StAr

®

 

partner, gE has determined 

that this product meets the 

EnErgy StAr guidelines 

for energy efficiency.

23-7/8"

Behind

Frame

90

°

 Door Swing

4" Min.

to Wall

20-5/8"

19"

130° Door Swing

13"

    

*84" From

Floor to

Top Frame

36" 

Frame to Frame

35" 

Case Width

*83-1/2" 

at

Rear

25-3/4"

27-3/4"

including

handle

Water and electrical locations

 

The opening must be prepared with the electrical and water 

supply located as shown.

The cutout depth must be 24".

The refrigerator will project forward, slightly beyond 

adjacent cabinetry, depending on your installation.

The cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot exceed the 

24" installation depth shown. The top case trim overlaps the 

bottom of the soffit.

Additional Specifications

•  A 115 volt 60Hz., 15 or 20 amp power supply is required. 

An individual properly grounded branch circuit or circuit 

breaker is recommended. Install a properly grounded 3-

prong electrical receptacle recessed into the back wall. 

Electrical must be located on rear wall as shown.

Note:

 GFI (ground fault interrupter) is not recommended.

•  Water line can enter the opening through the floor or back 

wall. The water line should be 1/4" O.D. copper tubing or  

GE SmartConnect

 kit between the cold water line and  

water connection location, long enough to extend to the  

front of the refrigerator. Installation of an easily accessible 

shut off valve in the water line is recommended.

The Installation Space

*  Shipping height.  

The refrigerator  

can be adjusted to 

fit into a cutout that 

is 83-1/2" min. to 

84-1/2” max. height. 

Note that the top 

case trim at the  

front is 1/2" higher 

and will overlap 

upper cabinetry or 

soffit. Use leveling 

legs and wheels 

for a maximum 1" 

height adjustment.

Product Clearances

These refrigerators are equipped with a 2 position door stop. 

The factory set 130° door swing can be adjusted to 90° if 

clearance to adjacent cabinets or walls is restricted.

Allow minimum clearances for freezer door and fresh food 

door for a full 130° door swing and to allow for pan removal.
4" minimum clearance is required when door swing is 

adjusted to 90°.  If the 90° door stop position is used, pan 

access is maintained, but pan removal is restricted.

Installation Information: Before installing, consult  

installation instructions packed with product, or online  

at Monogram.com, for current dimensional data.

*Finished Width

6"

5"

Electrical

Area

84-1/2" max

83-1/2" min

Finished

Opening

75" From Floor

to Bottom

of Electrical

Area

24"

5"

5"

3-1/2"

Water Supply

3-1/2"

36" Models 12"

42" Models 18"

48" Models 20"

696Dia15

Summary of Contents for Monogram ZIS360NX







Reviews: