![background image](http://html.mh-extra.com/html/ge/monogram-zic360nm/monogram-zic360nm_datasheet_2204241001.webp)
Monogram.
™
ZIC360NM – GE Monogram 36" Built-In Bottom Freezer Refrigerator with
Automatic Icemaker
Water and Electrical Locations
Electrical and water supply must be located as shown.
The cutout depth must be 24"
Designed for industry standard flush installation. The refrigerator will
project forward, slightly beyond adjacent cabinetry, depending on
your installation.
Cutout depth beneath a soffit
When installed beneath a soffit, the soffit cannot exceed the 24" installation
depth shown. The top case trim overlaps the bottom of the soffit.
Frameless Cabinets
The case trim overlaps cabinets at the top and sides. Therefore, frameless
cabinets may require filler strips to prevent interference with cabinet
door swing. The opening must allow for filler strips.
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual
properly grounded branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical receptacle recessed
into the back wall. Electrical must be located on rear wall as shown.
Note:
GFI (grounded fault interrupter) is not recommended.
• Water line can enter the opening through the floor or back wall. The
water line should be 1/4" O.D. copper tubing between the cold water
line and water connection location, long enough to extend to the
front of the refrigerator. Installation of an easily accessible shut off
valve in the water line is recommended.
Optional Panel Kits:
• ZPBC360: Black Panel Kit
• ZPWC360: White Panel Kit
• ZPSC360: Stainless Steel Panel Kit
Optional Custom Trim Kits:
• ZKHCSS2: Tubular Stainless Steel handles
• ZUG2: Unified Grille Kit
Product Clearances
These refrigerators are equipped with a 2 position door stop. The
factory set 130° door swing can be adjusted to 90° if clearance to
adjacent cabinets or walls is restricted.
Allow 25" minimum clearance for a full 130° door swing. Allow 15" for
pan removal.
4" minimum clearance is required when door swing is adjusted to 90°.
If the 90° door stop position is used, pan access is maintained, but pan
removal is restricted.
36"
Frame to Frame
Width
*84" From
Floor to
Top Frame
35"
Case Width
*83-1/2"
at
Rear
23-7/8"
Behind
Frame
36-3/4"
4" Minimum
to Wall
90
°
Door Swing
90
°
25"
Minimum
to Wall
130
°
Door Swing
130
°
The Installation Space
7"
Wall View
Electrical
Area
84-1/2" max
83-1/2" min
Finished
Opening
74-1/2" From
Floor to Bottom
of Electrical
10"
5"
3 1/2"
5"
3 1/2"
Water Supply
24" Cutout Depth
35-1/2"
Finished Width
2-5/16"
The finished cabinet width must be 35-1/2".
Dimensions and Clearances
* Shipping height. The refrigerator
can be adjusted to fit into a
cutout that is 83-1/2" min. to
84-1/2" max. height. Note that
the top case trim at the front
is 1/2" higher and will overlap
upper cabinetry or soffit. Use
leveling legs and wheels for
height adjustment.
Specification Revised 8/02
For answers to your Monogram,
®
GE Profile
™
or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center
®
service, 800.626.2000.
R
Listed by
Underwriters
Laboratories