GE MAC 600 SPY Service Manual Download Page 75

Page: 75 / 127

Revision G

MAC

600

4-25

2047426-002

Maintenance:

Check out Procedure

Measuring Circuit [M] and the displayed values are converted to leakage
current.

Earth Leakage (AC line) Current Test

This test measures leakage current of the device. The device has to be
turned on and off, and connected to your safety-testing equipment.

Measurements should be taken under the following conditions (refer to

“Electrical Safety Tests”

on page 4-24):



Device in ON state



Polarity switch NORM and RVS



S1 (neutral) closed and open



GND switch open

The test has failed if the measured values are greater than:

N.C.

S.F.C

Polarity: NORM & RVS
S1 (neutral): closed
GND: open

Polarity: NORM & RVS
S1 (neutral): open
GND: open

Total tests/combinations: 2

Summary of Contents for MAC 600 SPY
































































































































Search results

Summary of Contents for MAC 600 SPY

Reviews:

Related manuals for MAC 600 SPY

Brands by name

Popular brands

GE MAC 600 SPY, Service Manual

Search results

Summary of Contents for MAC 600 SPY

Reviews:

Related manuals for MAC 600 SPY

Brands by name

Popular brands