JS630SF
GE
Appliances 30" Slide-In Electric Range
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
Specification Revised 1/16
For answers to your Monogram, GE Café
™
Series, GE Profile
™
Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center
®
Service, 800.626.2000.
OPTIONAL KITS FOR SLIDE-IN ELECTRIC RANGES
WB07T10680 - Black Filler Strip Assembly
ACCESSORY BACKGUARDS
(Attaches to the back of range as a backguard when unit is
installed in 30" free-standing cutout)
JXS32SS (Stainless) - 4" High
JXS32BB (Black) - 4" High
BODY SIDES
(Slide-in ranges are sold
without sides installed. Can
be installed on either left
or right when unit has one
exposed side [no cabinet
adjacent]. Kit contains
1 body side) JXS77BB (Black)
All GE ranges are equipped with
an Anti-Tip device. The installation
of this device is an important,
required step in the installation
of the range.
NOTE: Use a 4' powercord
to prevent interference with
the storage drawer. Power
cords 4-1/2' to 6' long may
have to be dressed to allow
for proper drawer closing.
*Total depth from wall to
front of closed oven door
including handle is
28-1/2"
Accessory
Backguard JXS32
Recommended
6"
Min.
From Walls
30"
Min.
30"
Min.
15"
Min.
23-3/16"
35-7/8"-36-1/2"
from
Floor to countertop
2-7/8"
To Front
Surface of
Countertop
20-5/8"
Door
Clearance
From Front
Surface of
Countertop
25-3/4"*
(excluding handle)
If the control panel
measures 31-1/8"
(79.1 cm) like in the
illustration AND if the
countertop has a
raised edge, shave
raised edge to clear
the control panel,
as shown at left.
2-1/2"
4"
1-1/4"
Min. from
countertop to top
of cabinet drawer
Acceptable electrical
outlet area
2-1/2"
9-1/16"
7-1/2"
25"
29-15/16"-30-1/16"
24"
4"
31-1/4"
36-1/4"
30"
1-1/4"
Min. Flat
If the countertop area is not flat, excess tension may be applied to the glass cooktop, causing
breakage and voiding the warranty. Make sure the wall covering, countertop, flooring and
cabinets around the range can withstand the heat (up to 200°F) generated by the range.
A. Allow
30"
minimum clearance between surface units and bottom of unprotected wood or
metal cabinet, or allow a
24"
minimum when bottom of wood or metal cabinet is protected by no
less than
1/4"
-thick flame-retardant millboard covered with no less than No. 28 MSG sheet
metal (
.015"
thick),
.015"
-thick stainless steel,
.025"
aluminum or
.020"
copper.
B. This appliance has been approved for
0"
spacing to adjacent surfaces above the cooktop.
However, a minimum
6"
spacing to surfaces less than
15"
above the cooktop and adjacent
cabinetry.
is recommended to reduce exposure to steam, grease splatter and heat. Allow
1/4"
minimum
clearance at the back wall.
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage
space above the cooktop should be avoided. If cabinet storage space is to be provided above
the cooktop, the risk can be reduced by installing a range hood that projects at least
5"
beyond
the front of the cabinets.
If you are NOT using the
Filler strip or Backguard:
If you are using the
Filler strip or Backguard:
23-3/16"
30"
25"
30"
KW RATING
240V 11.9
208V 8.9
BREAKER SIZE
240V 40 Amps
†
208V 40 Amps
†
†
NOTE:
Check local codes
for required breaker size.
NOTE: Use a 4' powercord
to prevent interference with
the storage drawer. Power
cords 4-1/2' to 6' long may
have to be dressed to allow
for proper drawer closing.
*Total depth from wall to
front of closed oven door
including handle is
28-1/2"
Accessory
Backguard JXS32
Recommended
6"
Min.
From Walls
30"
Min.
30"
Min.
15"
Min.
23-3/16"
35-7/8"-36-1/2"
from
Floor to countertop
2-7/8"
To Front
Surface of
Countertop
20-5/8"
Door
Clearance
From Front
Surface of
Countertop
25-3/4"*
(excluding handle)
If the control panel
measures 31-1/8"
(79.1 cm) like in the
illustration AND if the
countertop has a
raised edge, shave
raised edge to clear
the control panel,
as shown at left.
2-1/2"
4"
1-1/4"
Min. from
countertop to top
of cabinet drawer
Acceptable electrical
outlet area
2-1/2"
9-1/16"
7-1/2"
25"
29-15/16"-30-1/16"
24"
4"
31-1/4"
36-1/4"
30"
1-1/4"
Min. Flat
If the countertop area is not flat, excess tension may be applied to the glass cooktop, causing
breakage and voiding the warranty. Make sure the wall covering, countertop, flooring and
cabinets around the range can withstand the heat (up to 200°F) generated by the range.
A. Allow
30"
minimum clearance between surface units and bottom of unprotected wood or
metal cabinet, or allow a
24"
minimum when bottom of wood or metal cabinet is protected by no
less than
1/4"
-thick flame-retardant millboard covered with no less than No. 28 MSG sheet
metal (
.015"
thick),
.015"
-thick stainless steel,
.025"
aluminum or
.020"
copper.
B. This appliance has been approved for
0"
spacing to adjacent surfaces above the cooktop.
However, a minimum
6"
spacing to surfaces less than
15"
above the cooktop and adjacent
cabinetry.
is recommended to reduce exposure to steam, grease splatter and heat. Allow
1/4"
minimum
clearance at the back wall.
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage
space above the cooktop should be avoided. If cabinet storage space is to be provided above
the cooktop, the risk can be reduced by installing a range hood that projects at least
5"
beyond
the front of the cabinets.
If you are NOT using the
Filler strip or Backguard:
If you are using the
Filler strip or Backguard:
23-3/16"
30"
25"
30"
NOTE: Use a 4' powercord
to prevent interference with
the storage drawer. Power
cords 4-1/2' to 6' long may
have to be dressed to allow
for proper drawer closing.
*Total depth from wall to
front of closed oven door
including handle is
28-1/2"
Accessory
Backguard JXS32
Recommended
6"
Min.
From Walls
30"
Min.
30"
Min.
15"
Min.
23-3/16"
35-7/8"-36-1/2"
from
Floor to countertop
2-7/8"
To Front
Surface of
Countertop
20-5/8"
Door
Clearance
From Front
Surface of
Countertop
25-3/4"*
(excluding handle)
If the control panel
measures 31-1/8"
(79.1 cm) like in the
illustration AND if the
countertop has a
raised edge, shave
raised edge to clear
the control panel,
as shown at left.
2-1/2"
4"
1-1/4"
Min. from
countertop to top
of cabinet drawer
Acceptable electrical
outlet area
2-1/2"
9-1/16"
7-1/2"
25"
29-15/16"-30-1/16"
24"
4"
31-1/4"
36-1/4"
30"
1-1/4"
Min. Flat
If the countertop area is not flat, excess tension may be applied to the glass cooktop, causing
breakage and voiding the warranty. Make sure the wall covering, countertop, flooring and
cabinets around the range can withstand the heat (up to 200°F) generated by the range.
A. Allow
30"
minimum clearance between surface units and bottom of unprotected wood or
metal cabinet, or allow a
24"
minimum when bottom of wood or metal cabinet is protected by no
less than
1/4"
-thick flame-retardant millboard covered with no less than No. 28 MSG sheet
metal (
.015"
thick),
.015"
-thick stainless steel,
.025"
aluminum or
.020"
copper.
B. This appliance has been approved for
0"
spacing to adjacent surfaces above the cooktop.
However, a minimum
6"
spacing to surfaces less than
15"
above the cooktop and adjacent
cabinetry.
is recommended to reduce exposure to steam, grease splatter and heat. Allow
1/4"
minimum
clearance at the back wall.
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage
space above the cooktop should be avoided. If cabinet storage space is to be provided above
the cooktop, the risk can be reduced by installing a range hood that projects at least
5"
beyond
the front of the cabinets.
If you are NOT using the
Filler strip or Backguard:
If you are using the
Filler strip or Backguard:
23-3/16"
30"
25"
30"
NOTE: Use a 4' powercord
to prevent interference with
the storage drawer. Power
cords 4-1/2' to 6' long may
have to be dressed to allow
for proper drawer closing.
*Total depth from wall to
front of closed oven door
including handle is
28-1/2"
Accessory
Backguard JXS32
Recommended
6"
Min.
From Walls
30"
Min.
30"
Min.
15"
Min.
23-3/16"
35-7/8"-36-1/2"
from
Floor to countertop
2-7/8"
To Front
Surface of
Countertop
20-5/8"
Door
Clearance
From Front
Surface of
Countertop
25-3/4"*
(excluding handle)
If the control panel
measures 31-1/8"
(79.1 cm) like in the
illustration AND if the
countertop has a
raised edge, shave
raised edge to clear
the control panel,
as shown at left.
2-1/2"
4"
1-1/4"
Min. from
countertop to top
of cabinet drawer
Acceptable electrical
outlet area
2-1/2"
9-1/16"
7-1/2"
25"
29-15/16"-30-1/16"
24"
4"
31-1/4"
36-1/4"
30"
1-1/4"
Min. Flat
If the countertop area is not flat, excess tension may be applied to the glass cooktop, causing
breakage and voiding the warranty. Make sure the wall covering, countertop, flooring and
cabinets around the range can withstand the heat (up to 200°F) generated by the range.
A. Allow
30"
minimum clearance between surface units and bottom of unprotected wood or
metal cabinet, or allow a
24"
minimum when bottom of wood or metal cabinet is protected by no
less than
1/4"
-thick flame-retardant millboard covered with no less than No. 28 MSG sheet
metal (
.015"
thick),
.015"
-thick stainless steel,
.025"
aluminum or
.020"
copper.
B. This appliance has been approved for
0"
spacing to adjacent surfaces above the cooktop.
However, a minimum
6"
spacing to surfaces less than
15"
above the cooktop and adjacent
cabinetry.
is recommended to reduce exposure to steam, grease splatter and heat. Allow
1/4"
minimum
clearance at the back wall.
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage
space above the cooktop should be avoided. If cabinet storage space is to be provided above
the cooktop, the risk can be reduced by installing a range hood that projects at least
5"
beyond
the front of the cabinets.
If you are NOT using the
Filler strip or Backguard:
If you are using the
Filler strip or Backguard:
23-3/16"
30"
25"
30"
RECEPTACLE LOCATIONS:
Locally approved flexible service cord or
conduit must be used because terminals are not accessible after range
installation. See shaded area in drawing for location of electrical outlet box.
Recommended outlet locations allow range to be installed directly against
rear wall.
NOTE:
This appliance has been approved for 0" spacing to adjacent
surfaces above the cooktop. However, a 6" minimum spacing to surfaces
less than 15" above the cooktop and adjacent cabinet is recommended to
reduce exposure to steam, grease splatter and heat.
INSTALLATION INFORMATION:
Before installing, consult installation
instructions for current dimensional data and additional requirements