background image

1

31-10612    

(12-04 JR)

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com

In Canada, call 1.800.361.3400 or Visit our Website at: www.geappliances.ca

Installation

36

Sealed Gas Cooktop

Instructions

BEFORE YOU BEGIN

Read these instructions completely 
and carefully.

IMPORTANT

Save these

instructions for local inspector’s use.

IMPORTANT 

Observe all

governing codes and ordinances.

Note to Installer – 

Be sure to leave these

instructions with the Consumer.

Note to Consumer – 

Keep these

instructions for future reference.

Product failure due to improper installation
is not covered under the Warranty.

WARNING 

This appliance must

be properly grounded.

IMPORTANT 

Leak testing of the

appliance shall be conducted according to
the manufacturer’s instructions.

Proper installation is the responsibility 
of the installer and product failure due to
improper installation is NOT covered under
warranty.

IN THE COMMONWEALTH OF
MASSACHUSETTS:

• 

This product must be installed by a
licensed plumber or gas fitter.

• 

When using ball-type gas shut-off valves,
they shall be the T-handle type.

• 

A flexible gas connector, when used, must
not exceed 3 feet.

JGP628, JGP630, JGP963, JGP970, 
JGP975, ZGU36

FOR YOUR SAFETY:

WARNING 

— If the information 

in this manual is not followed exactly, a fire,
explosion or gas leak may result causing
property damage, personal injury or death.

Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance!

WHAT TO DO IF YOU
SMELL GAS:

• 

Do not try to light any appliance. Do not
touch any electrical switch; do not use any
phone in your building.

• 

Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions. 

• 

If you cannot reach your gas supplier, call
the fire department.

Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.

This cooktop has been design certified 
by CSA International. You’ll find safety
precautions in your Owner’s Manual. 
Read them carefully.

• 

Installation of this cooktop must conform
with local codes or, in the absence of local
codes with the National Fuel Gas Code,
ANSI Z223.1/NFPA 54–Latest edition.

• 

Be sure your cooktop is installed properly
by a qualified installer or service technician.

• 

To eliminate reaching over surface burners,
cabinet storage above burner should be
avoided.

• 

Do not install the unit near an outside door
or where a draft may affect its use.

WARNING 

Disconnect all

electrical power at the main circuit breaker 
or fuse box before installing.

Summary of Contents for JGP633SETSS

































Reviews: