JD750DF
GE 30" Drop-In Electric Convection Range
Specification Created 5/13
320832
Listed by
Underwriters
Laboratories
Dimensions and Installation Information (in inches)
IMPORTANT:
30" DROP-IN RANGES ARE DESIGNED TO HANG FROM THE COUNTERTOP.
IT DOES NOT REST ON THE FLOOR. FOR INSTALLATION ALTERNATIVES, REFER TO
INSTALLATION INSTRUCTIONS.
Note:
This appliance has been approved for 0” spacing to adjacent surfaces
above the cooktop. However, a 6” minimum spacing to surfaces less than 15”
above the cooktop and adjacent cabinet is recommended to reduce exposure
to steam, grease splatter and heat.
Optional Kits For Drop-In Electric Ranges
(Available At Additional Cost)
Installation information:
Before installing, consult installation instructions
for current dimensional data and additional requirements.
Acceptable Electrical Outlet
Area Also In Adjacent
Cabinet Or Under Floor
Conduit is 40" long
30" Min.
30" Min.
15" Min.
Recommended
6" Min.
from walls
2-7/8"
To Front Surface
of Countertop
30
27-1/2
25
23-3/16
If necessary,
build upsides
to 1-1/4" thick
to provide
countertop
support
27
20-5/8" Door
Clearance
From Front
Surface of
Countertop
24
31-1/4
30
4
Accessory
Backguard
JXS32
25-3/4*
(excluding handle)
*Total depth from wall to
front of closed oven door
including handle is 28-1/2.
28-1/2
Acceptable Electrical Outlet
Area Also In Adjacent
Cabinet Or Under Floor
Conduit is 40" long
30" Min.
30" Min.
15" Min.
Recommended
6" Min.
from walls
2-7/8"
To Front Surface
of Countertop
30
27-1/2
25
23-3/16
If necessary,
build upsides
to 1-1/4" thick
to provide
countertop
support
27
20-5/8" Door
Clearance
From Front
Surface of
Countertop
24
31-1/4
30
4
Accessory
Backguard JXS32
25-3/4*
(excluding handle)
*Total depth from wall to
front of closed oven door
including handle is 28-1/2.
28-1/2
Accessory Backguards
(Attaches to the back of range
as a backguard when unit is installed
in 30" free-standing cutout)
JXS32SS (Stainless) - 4" High
JXS32BB (Black) - 4" High
Rear Filler Strip
WB07T10680 - Black Filler Strip Assembly
For answers to your Monogram
®
or GE
®
appliance questions, visit our website at
geappliances.com or call GE Answer Center
®
service, 800.626.2000.
All GE ranges are equipped with
an Anti-Tip device. The installation
of this device is an important,
required step in the installation
of the range.
ADA qualified based
on Uniform Federal
Accessibility Standards
*
Acceptable
Electrical
Outlet Area
30" Min.
30" Min.
Shave Raised Edge To Clear
31-1/8" Wide Control Panel
Excluding Model JSS28
2-7/8"
To Front
Surface Of
Countertop
20-5/8" Door
Clearance
From Front
Surface of
Countertop
31-1/4
30
25-3/4*
Recommended
6" Min.
From Walls
23-3/16
15" Min.
4
2-1/2
30
25
9/16
7-1/2
2-1/2
Accessory
Backguard
JXS32
24
36-1/4
(excluding handle)
*Total depth from wall to
front of closed oven door
including handle is 28-1/2.
35-7/8"–38"
from floor to
countertop
If the countertop area is not flat, excess tension may be applied to the glass cooktop, causing breakage and
voiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the range can
withstand the heat (up to 200°F) generated by the range.
A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or metal cabinet, or
allow a 24" minimum when bottom of wood or metal cabinet is protected by no less than 1/4"-thick
flame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015" thick), .015"-thick stainless
steel, .025" aluminum or .020" copper.
B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop.
However, a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent cabinetry
is recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimum
clearance at the back wall.
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above the
cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk can be reduced
by installing a range hood that projects at least 5" beyond the front of the cabinets.
23-3/16
30
30
If you are NOT using the
Filler strip or Backguard:
If you are using the
Filler strip or Backguard:
25
Acceptable
Electrical
Outlet Area
30" Min.
30" Min.
Shave Raised Edge To Clear
31-1/8" Wide Control Panel
Excluding Model JSS28
2-7/8"
To Front
Surface Of
Countertop
20-5/8" Door
Clearance
From Front
Surface of
Countertop
31-1/4
30
25-3/4*
Recommended
6" Min.
From Walls
23-3/16
15" Min.
4
2-1/2
30
25
9/16
7-1/2
2-1/2
Accessory
Backguard
JXS32
24
36-1/4
(excluding handle)
*Total depth from wall to
front of closed oven door
including handle is 28-1/2.
35-7/8"–38"
from floor to
countertop
If the countertop area is not flat, excess tension may be applied to the glass cooktop, causing breakage and
voiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the range can
withstand the heat (up to 200°F) generated by the range.
A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or metal cabinet, or
allow a 24" minimum when bottom of wood or metal cabinet is protected by no less than 1/4"-thick
flame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015" thick), .015"-thick stainless
steel, .025" aluminum or .020" copper.
B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop.
However, a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent cabinetry
is recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimum
clearance at the back wall.
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above the
cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk can be reduced
by installing a range hood that projects at least 5" beyond the front of the cabinets.
23-3/16
30
30
If you are NOT using the
Filler strip or Backguard:
If you are using the
Filler strip or Backguard:
25
KW Rating
240V
13.5
208V
10.1
Breaker Size
240V
40 Amps
†
208V
40 Amps
†
†
Note:
Check local codes for required breaker size.
