background image

TOOLS YOU WILL NEED

CAUTION: BEFORE YOU BEGIN

Read these instructions carefully and completely.

IMPORTANT –

 Save these instructions for local

inspector’s use.

IMPORTANT –

 Observe all governing codes and

ordinances.

Note to Installer – 

Be sure to leave these instructions with

the Consumer.

Note to Consumer –

 Keep these instructions for future

reference.

30” Electric Cooktop

Installation
Instructions

JCP340BC, JCP340WC, JCP350BC, JCP350WC,
JCP930BC, JCP930SC, JCP930TC

NOTE:

 This appliance must be properly grounded.

Skill level – 

Installation of this appliance requires basic

mechanical and electrical skills.

Completion time – 

2–3 hours.

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not

covered under the Warranty.

PARTS INCLUDED

1/8” Drill Bit &
Electric or Hand Drill

Phillips
Screwdriver

Foam Strips

4 screws

Pub. No. 31-10428

229C

4053P127

1

1

1

1

1

If you have questions, call 800-361-3400 or visit our Website at: www.GEappliances.ca

2 Hold Down Brackets

Ruler or
Straightedge

Hand or
Saber Saw

Pencil

Junction
Box

Wire Nuts

MATERIALS NEEDED

Summary of Contents for JCP340BC









Reviews: