background image

1

229C

4053P545-5

31-10556-5

06-04 JR

EER3000, EER3001, JBP24, JBP25, JBP26, JBP35, JBP48, JBP64, JBP66, JBP67, JBP68, JBP69,
JBP71, JBP78, JBP80, JBP82, JBP83, JBP84, JBP99, JB600, JB710, JB905, JB968, JB988, JBS55

Installation

Free-Standing

Instructions

Electric Ranges

BEFORE YOU BEGIN

Read these instructions completely 
and carefully.

IMPORTANT 

Save these

instructions for local inspector’s use.

IMPORTANT 

Observe all

governing codes and ordinances.

Note to Installer – 

Be sure to leave these

instructions with the Consumer.

Note to Consumer – 

Keep these

instructions for future reference.

Skill level – 

Installation of this appliance

requires basic mechanical skills.

Completion time – 

1 to 3 hours

Proper installation is the responsibility of
the installer. 

Product failure due to improper installation
is not covered under the Warranty.

WARNING 

This appliance must

be properly grounded.

FOR YOUR SAFETY:

WARNING 

Before beginning the

installation, switch power off at service panel
and lock the service disconnecting means to
prevent power from being switched on
accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to
the service panel.

ANTI-TIP DEVICE

WARNING 

To reduce the risk 

of tipping, the appliance must be secured by
properly installed Anti-Tip bracket packed
with this appliance.

If the Anti-Tip device supplied with the range
does not fit this application, use the universal
Anti-Tip device WB2X7909.

WARNING

• 

All ranges can tip

• 

Injury to persons could result

• 

Install Anti-Tip bracket packed
with range

• 

See Installation Instructions

If you pull the range out and away from the
wall for any reason, make sure the Anti-Tip
bracket is engaged when the range is pushed
back against the wall.

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com

Summary of Contents for JBP99













Reviews: