manualshive.com logo in svg

GE IDP-1111, User Manual, Page: 107 / 114

Share
Download
GE IDP-1111 User Manual Download Page 107

99

Upgrading from v1.8.5 to v1.8.6

To upgrade the software from v1.8.5 to v1.8.6, do the following: 

1. Download the filename 

v.1.8.6.gz

 from 

www.gesecurity.com

 to your computer. You can at the same 

time also download 

v2.1.9.ge

 to have it readily available.

2. If possible, set up your computer and video monitor near each other so that you can view all upgrade 

messaging. 

3. Connect a computer (laptop or desktop) to the Ethernet connection on the housing board in the housing.

•

Use a crossover cable if you are connecting the computer directly to the dome. 

•

Use a standard Ethernet cable if you are connecting the computer to the dome through a 
hub device.

4. Make sure that the computer you are using has the same IP subnet and the same IP range as the dome.

The default addresses are:

•

IP for domes: 192.168.208.XXX, where XXX is the site number (or camera address) of the dome.

•

Subnet mask for domes: 255.255.255.0. 

5. Open Microsoft Internet Explorer.

6. Enter your dome’s IP address into the address box in the form of http:

 

//XXX.XXX.XXX.XXX/

update.htm.

7. Press 

Enter

 or click 

Go

.

8. If this is the first time you are accessing the web browser for the dome after it has rebooted, you will be 

asked to log on to the dome. See 

Figure 61

 on page 100.

•

Only installers have passcode permission to upgrade software.

•

You need to type in the user name, which is 

Installer

, with a capital letter 

I

.

•

Finally, you need to use the same passcode as is used for accessing the dome’s programming 
interface. If the Installer passcode was not specified for the programming interface, leave the 
passcode box blank.

CAUTION:  

DO NOT interrupt the upgrade process until it has completed. Don’t use the keypad, don’t break the network 
connection, and don’t cycle the power to the dome.

CAUTION:  

When flashing software upgrades to the dome over a standard IP network via the dome’s Ethernet connection, 
ensure that the network is secured from unauthorized access. Consider connecting the Ethernet cable only 
when you are flashing the dome, unless you have the dome connected to a secure, isolated network.

CAUTION:  

Do not use the TFTP programming interface option from the  

Firmware Update

 feature of the 

System

 menu for this software upgrade. This upgrade will be removing that option.

Summary of Contents for IDP-1111



















































































































Reviews:

No comments