GE Hydran 201i, Instruction Manual

Page: 23 / 300

Hydran 201
i
System
Part 17997 Rev. 6, March 2011 xxiii
LIST OF FIGURES
Figure 1-1 - Hydran 201T i Intelligent Transmitter . . . . . . . . . . . . . 1-3
Figure 1-2 - Hydran 201C i -C Communications Controller . . . . . . . . . . 1-4
Figure 1-3 - Hydran 201C i -1 One-Channel Controller . . . . . . . . . . . 1-5
Figure 1-4 - Hydran 201TW Tube Wrench . . . . . . . . . . . . . . . . 1-8
Figure 1-5 - Vibration-Absorbing Rubber Pads . . . . . . . . . . . . . . 1-9
Figure 2-1 - Hydran 201T i ’s Enclosure (Mounted on a Valve) . . . . . . . . 2-3
Figure 2-2 - Internal View of the Hydran 201T i . . . . . . . . . . . . . . 2-5
Figure 2-3 - Hydran 201 Sensor . . . . . . . . . . . . . . . . . . . . 2-6
Figure 2-4 - First View of the Top Side of the I/O Module . . . . . . . . . . 2-8
Figure 2-5 - Second View of the Top Side of the I/O Module . . . . . . . . . 2-9
Figure 2-6 - Left Side of the I/O Module . . . . . . . . . . . . . . . . . 2-10
Figure 2-7 - Right Side of the I/O Module . . . . . . . . . . . . . . . . 2-12
Figure 3-1 - Typical Configuration of a Hydran 201 i System . . . . . . . . . 3-1
Figure 3-2 - Internal View of the Hydran 201C i -C . . . . . . . . . . . . . 3-3
Figure 3-3 - Circuit Board of the Hydran 201C i -C . . . . . . . . . . . . . 3-5
Figure 3-4 - Hydran 201R Model i . . . . . . . . . . . . . . . . . . . 3-8
Figure 3-5 - External View of the Hydran 201C i -1 . . . . . . . . . . . . . 3-9
Figure 3-6 - Internal View of the Hydran 201C i -1 . . . . . . . . . . . . . 3-11
Figure 3-7 - Circuit Board of the Hydran 201C i -1 . . . . . . . . . . . . . 3-12
Figure 4-1 - Hydran 201T i ’s User Interface . . . . . . . . . . . . . . . . 4-2
Figure 4-2 - Hydran 201T i ’s Keypad . . . . . . . . . . . . . . . . . . 4-8
Figure 5-1 - H201T i ’s Serial Number and Protective Cap . . . . . . . . . . 5-1
Figure 5-2 - Do Not Touch the Membrane . . . . . . . . . . . . . . . . 5-2
Figure 5-3 - Do Not Paint the Sensor or Clean It With Any Solvent . . . . . . 5-3
Figure 5-4 - Use the Hydran 201TW Instead of a Pipe Wrench . . . . . . . . 5-4
Figure 5-5 - Do Not Install the H201T i on the Inlet Side of the Radiator Pump . . 5-5
Figure 5-6 - Do Not Install the H201T i on an Elbow . . . . . . . . . . . . 5-6
Figure 5-7 - Avoid High-Pressure Water Streams . . . . . . . . . . . . . 5-6
Figure 5-8 - Typical Installation of the Hydran 201 i System . . . . . . . . . 5-8
Figure 5-9 - Mounting Locations of the H201T i on a Transformer . . . . . . . 5-10
Figure 6-1 - Example of Test Certificate and Data Sheet for the Hydran 201T i . . 6-4