manualshive.com logo in svg

GE H49021AA, Basic Service Manual, Page: 143 / 420

Share
Download
GE H49021AA Basic Service Manual Download Page 143

GE M

EDICAL

 S

YSTEMS

 

D

IRECTION

 5184024-100, R

EVISION

 5

LOGIQ

WORKS

® B

ASIC

 S

ERVICE

 M

ANUAL

 

Chapter 3 Installation

3-77

3-5-1-5

Keyboard setup

Depending on your order you will receive a non-US keyboard. All keyboard input locales will be pre 
configured. Please check whether settings are correct.

1.) Click on the keyboard setup button, the following window will appear:

NOTE

This Procedure is not required if the keyboard is a US keyboard, since the default setting is set to US, 
English keyboards.

Figure 3-66  Keyboard Status Window

Summary of Contents for H49021AA





































































































































































































































































































































































































































Reviews:

No comments