manualshive.com logo in svg

GE FVP110, Maintenance Manual

Share
Download
GE FVP110 Maintenance Manual Download Page 285

269

 Maintenance of Flameproof 

Installation and Operating

Maintenance of Flameproof Apparatus

To maintain the flameproof apparatus, do the following.

Maintenance 
servicing with the 
power on

Flameproof apparatus shall not be maintenance-serviced with 
its power turned on. However, in cases where maintenance ser-
vicing is to be conducted with the power turned on, with the 
equipment cover removed, always use a gas detector to check 
that there is no explosive gas in that location. If it cannot be 
checked whether an explosive gas is present or not, mainte-
nance servicing shall be limited to the following two items:

❑

Visual inspection - Visually inspect the flameproof 
apparatus, metal conduits, and cables for damage or 
corrosion, and other mechanical and structural defects.

❑

Zero and span adjustments - These adjustments should 
be made only to the extent that they can be conducted 
from the outside without opening the equipment cover. In 
doing this, great care must be taken not to cause 
mechanical sparks with tools.

Summary of Contents for FVP110





































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands