manualshive.com logo in svg

GE FVP110, Maintenance Manual

Share
Download
GE FVP110 Maintenance Manual Download Page 166

 FVP 110 Fieldbus Valve Positioner Manual

150

 GE Energy

Figure 67

Function Diagram of SIGSEL Function Block

Function Supported

This block is intended to be used in a forward path only and is not intended to receive 
signals from the output of a controller. There is no back calculation support or propagation 
of control status values. The processing of the block is as follows.

Input Processing

If DISABLE_n is true then don’t process (ignore) the respective input IN_n.

Process the Use Uncertain as Good status options. Discard (ignore) inputs whose status 
is bad.

If there are no inputs left, or fewer than MIN_GOOD inputs, then set the value of 
SELECTED to zero. Do not do selection processing.

Selection Processing

If OP_SELECT is non-zero, the OP_SELECT value shall determine the selected input, 
regardless of the SELECT_TYPE selection. Set SELECTED to the number of the input 
used.

If SELECT_TYPE is First Good, transfer the value of the first remaining input to the 
output of the block. Set SELECTED to the number of the input used.

If SELECT_TYPE is Minimum, sort the remaining inputs by value. Transfer the lowest 
value to the output of the block. Set SELECTED to the number of the input with the lowest 
value.

If SELECT_TYPE is Maximum, sort the remaining inputs by value. Transfer the highest 
value to the output of the block. Set SELECTED to the number of the input with the 
highest value.

Summary of Contents for FVP110





































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands