Microphone
Flash button
Speaker button
Redial button
Message indicator
In use indicator
Display
Dial button
Down button
Store button
Memory button
Contrast
Mute
button
Out call button
Delete button
Set button
I
NTRODUCTION
Your Caller ID phone stores and displays specific information, provided by your
local telephone company, to subscribers of Caller ID or similar caller
identification services.
·
FSK/DTMF Caller ID auto detect
·
Incoming call log records up to 68 calls
·
Outgoing call log records up to 15 last dialed numbers
·
10 two-touch memories
·
On hook pre-dialing
·
Prefix Code
·
Redial
·
Pulse or Tone dialing mode
·
Mute function
·
Speakerphone
M
AIN
F
EATURES
Your Caller ID phone enables you to:
·
Identify callers before you answer the phone.
·
View the time and date of each incoming call.
·
Record up to 68 Caller ID messages sequentially.
To get the most from your new phone, please read through this user's
guide.
SHORT GLOSSARY OF TERMINOLOGY USED IN THIS MANUAL
Hook switch.
The part of the base that pops up to activate the phone line
when the handset is lifted from the base.
Off-hook.
A term used to describe the phone in its active mode; when the
handset is off the base cradle or when the
SPEAKER
button is pressed.
On-hook.
A term used to describe the phone in its inactive mode.
NOTE:
If you find any of the parts missing, please contact the store where
this product was purchased.
Base
Handset
Coil cord
Modular telephone line jack
Wall plate
To use this phone, you need a RJ11C type modular
telephone jack (similar to the one pictured here),
installed in your home. Call your local phone
company to get one installed.
TELEPHONE JACK REQUIREMENTS
Telehone
line cord
User ’s Guide
3
2
INSTALLING THE PHONE
Your phone should be placed on a level surface, such as a desk or
table top, or you can mount it on a wall.
BATTERY
1. If the telephone line cord is connected, disconnect it from the base unit.
2. Carefully turn the phone over
the battery compartment by
pushing on the battery cover and sliding it away from the unit .
3. Insert 3 AA-size alkaline batteries (not included) as shown
on the diagram in the battery compartment .
4. Snap the battery compartment door back
into place.
5. If the line cord was previously connected,
reattach it to the unit and check your
memory locations.
and open
Wall mounting knob
location
0
Rotate 180
WALL MOUNTING:
The knob is designed to keep this
unit in place when the telephone is vertical on the wall.
2. Install the base unit to the wall and then plug one end of line cord into the
junction box and the other end into the modular telephone line jack marked
“
”
.
3. Fix the telephone in the wall as shown in the following layout.
WALL MOUNTING
1.Rotate the wall mounting knob as shown in the following layout:
1. Connect the handset.
2. Connect the telephone line.
IMPORTANT:
If you are not going to use the telephone for more than
30 days, remove the batteries.
I
NSTALLATION
CAUTION:
Disconnect the phone cord from the wall outlet
before installing or replacing the batteries.
·
Never install telephone wiring during a lighting storm.
·
Never touch un-insulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
·
Read caution when installing or modifying telephone lines.
·
Never install telephone jack in wet location unless the jack is
specifically designed for wet locations.
·
Temporarily disconnect any equipment connected to the phone,
such as faxes, other phones or modems.
INSTALLING AND REPLACING THE BATTERIES
Your Caller ID phone uses 3 AA-Size alkaline batteries for receiving and
storing Caller ID records and for storing the numbers you use frequently.
Phone number display
O
PTIONS
M
ENU
Outgoing call
New Caller,
Repeat Caller
Mail information
MUTE
OUT
D
M
IN
Speakerphone
Day
Minutes
Incoming Call
Week display
Mute Mic
Hour
Month
Call-log Number
1
2
S
ETTING THE
P
HONE
There are 4 options to set:
Date and Time Setting.
Pcode is a prefix code that user may add to the front of
the number before dialing.
Select the dialing mode. This is dependent on the
telephone company you are connected to.
Timing setting. This timing allows user to momentarily
access telephone services (such as call waiting) when
FLASH button is pressed.
MAKING A PHONE CALL
The number shown will be dialed
Dial number
Dial number
The number shown
will be dialed
REVIEWING OUTGOING NUMBERS
DIAL BACK AN OUTGOING NUMBER
Caller ID (CID) is a service available from your local telephone company.
For Caller ID to work on this system, you must subscribe to Caller ID
service. This unit can receive caller ID without any setting. The Caller ID
information may include the phone number, date and time.
CALLER ID FEATURES
REVIEWING INCOMING CALLS
Add number
to the front
The number shown
will be dialed
Select the
caller number
OR
OR
DIAL BACK A CALLER ID NUMBER
Select the
caller number
The number
shown will be dialed
Select the
caller number
Press
“
0
”
key for 2
seconds, PCODE will
be added to the front
of number shown
The number shown will be dialed
Reviewing Incoming Call Log
MUTE
In off-hook state press the
MUTE
button to activate the mute function.
When
MUTE
is on, the
MUTE
indicator will show on the screen.
Press the
MUTE
button to exit mute
function and resume normal
conversation.
P=>T DIAL MODE
In PULSE dialing mode, press[*] button to access
TONE
service.
The number shown will be dialed
Last number redial
REDIAL
CONTRAST LEVEL ADJUSTMENT
Press the MUTE button to adjust the display contrast level when the
telephone is in on-hook states.
1
OR
correct a
mistake
OR
OR
OR
OR
OR
Desktop Corded Phone
with Caller ID* & Speakerphone
User’s Guide
Model EX30044
visit our website:
www.thehomephones.com
OR
OR
OR
OR
OR
OR
Desktop Corded Phone
with Caller ID* & Speakerphone
User’s Guide
Model EX30044
Ringer Volume Switch
Answer Call
End Call
Answer Call
Ringing
Ringing
SETTING DATE/TIME
Enter Year, Month,
Day and Time
Press and Hold
2 Seconds
SETTING PCODE
Press and Hold
2 Seconds
SETTING TONE/PULSE
Press and Hold
2 Seconds
Tone Pulse
Select Tone or Pulse
P
HONE
O
PERATION
RECEIVING A PHONE CALL
Answer Call
End Call
Answer Call
End Call
Ringing
Ringing
Option 1
SETTING FLASH
Press and Hold
2 Seconds
100/300/600
Select Timing
STORING OUTGOING NUMBERS INTO MEMORY
T
ROUBLESHOOTING
T
IPS
No Dial Tone
·
Check all connections are secure and not damaged.
·
Make sure the hook switch is fully extended when handset is lifted
from cradle.
No Display
·
Replace the batteries.
·
Check for proper battery installation.
No Information is Shown After the Phone Rings
·
Make sure you have subscribed to Caller ID service from your local
telephone company?
·
Be sure to wait until the second ring before answering a call.
Phone Dials in Pulse with Tone Service
·
Make sure T/P DIAL MODE is set to TONE DIAL.
Phone Will not Dial Out with Pulse Service
·
Make sure T/P DIAL MODE is set to PULSE DIAL.
Memory Location
Select a Memory Location
DIALING A MEMORY LOCATION
Select a Memory
Location
Press and Hold
2 Seconds
DELETING A MEMORY LOCATION
Phone Does Not Ring
·
You may have too many extension phones on one line. Try
unplugging some extension phones.
·
Check dial tone, see troubleshooting tips for no dial tone.
Incoming and Outgoing Voice Volume Low
·
Check if other phones are off hook at the same time. If so, this is a normal
condition. Volume drops when additional phones are used at once.
·
Check the handset receiver or speaker volume.
GENERAL PRODUCT CARE
To keep your phone in good operating condition, follow these guidelines:
·
Avoid placing near heating appliances and devices that generate
electrical noise (for example, motors or fluorescent lamps).
·
DO NOT expose to direct sunlight or moisture.
·
Avoid dropping and other rough treatment .
·
Wipe with a soft cloth.
·
Never use a strong cleaning agent or abrasive powder as this will
damage the
.
·
Retain the original packaging in case you need to ship it at a later date.
finish
Used equipment must be disposed of in compliance with current
environment protection regulations. You should return it to your
reseller or dispose of it in an approved recycling center.
OR
OR
OR
DELETING A CALLER ID NUMBER
M
EMORY
O
PERATIONS
STORING A TELEPHONE NUMBER
STORING AN INCOMING CALL NUMBER
Option 2
Option 3
Option 4
Option 1
Option 2
Option 1
Option 2
Option 1
Option 2
Option 3
Option 1
Option 2
Up button
End Call
Model EX30044
P/N: 830044-4103
Version 2 11/2010
Printed in China
©2010 CCT Tech Global Limited
is a trademark of
The General Electric Company
and is under license by
CCT Tech Global Limited,
Central, Hong Kong
Select the number
Memory Location
Select the number
Select the number
Memory location
Dial number
Memory location
Your package includes the following items:
P
ARTS
C
HECKLIST
Ex30044 80g
国产书写纸/单色双面印刷/扇形折页/两国语言(正面
English,
反面
Spanish) S:525X427mm
SIZE A A
SIZE A A
SIZE A A
