GE Corometrics 250cx Series Service Manual Download Page 203

Page: 203 / 252

Revision C

250cx Series Maternal/Fetal Monitor

6-11

2036947-001

Parts List, Drawings, and Replacement: Assembly/Disassembly of FRUs

Insert new Ultrasound board into Front-end Motherboard.

10. Reconnect Ultrasound cables to Ultrasound board connectors. The left-most

Ultrasound connector US1 cable goes to the rear connector on Ultrasound
board, J5.

11. Replace card cage cover. Re-insert screws.

12. Connect 8-conductor Inverter cable to DSP board connector J1.

13. Connect 20-conductor DSP-to-LCD Decoder ribbon cable to DSP board

connector J2.

14. Place DSP board onto Main board. Use two screws to fasten DSP board to

chassis.

15. Place top cover. Re-insert screws.

2025177-008 FECG/UA Board

1. Remove top cover. Keep screws aside.

Remove two screws fastening DSP board to chassis. Keep screws aside.

Remove DSP board from Main board, but do not fully remove from chassis.

Disconnect 8-conductor Inverter cable from DSP board connector J1.

Disconnect 20-conductor DSP-to-LCD Decoder ribbon cable from DSP board
connector J2.

Remove card cage cover. Keep screws aside.

(If MECG is installed)

Disconnect MECG cable from MECG board connector.

Remove MECG

(if installed)

and FECG board from Front-end Motherboard.

(If MECG is installed)

Remove two screws fastening MECG board to FECG

board.

10.

(If MECG is installed)

Remove MECG board from FECG board.

11.

(If MECG is installed)

Insert MECG board onto new FECG board and fasten

with two screws.

12. Insert MECG

(if installed)

and new FECG board into Front-End Motherboard.

13.

(If MECG is installed)

Connect MECG cable to MECG board connector.

14. Replace card cage cover. Re-insert screws.

15. Reconnect 8-conductor Inverter cable to DSP board connector J1.

16. Reconnect 20-conductor DSP-to-LCD Decoder ribbon cable to DSP board

connector J2.

17. Place DSP board onto Main board. Use two screws to fasten DSP board to

chassis.

18. Place top cover. Re-insert screws.

Summary of Contents for Corometrics 250cx Series



























































































































































































































































Search results

Summary of Contents for Corometrics 250cx Series

Reviews:

GE Corometrics 250cx Series, Service Manual, Page: 203 / 252

Search results

Summary of Contents for Corometrics 250cx Series

Reviews: