manualshive.com logo in svg

GE Corometrics 250cx Series, Service Manual, Page: 195 / 252

Share
Download
GE Corometrics 250cx Series Service Manual Download Page 195

Revision C

250cx Series Maternal/Fetal Monitor

6-3

2036947-001

Parts List, Drawings, and Replacement: Ordering Parts

Ordering Parts

This section of the manual provides parts lists for the 250cx Series Monitor. Parts 
lists should be used in conjunction with the other chapters of this manual.

GE makes every effort possible to provide the most up-to-date reference 
documentation for your equipment. However, in special cases involving field-
installed upgrades, the revision level of a diagram or parts list in this manual may 
not reflect the revision level of your unit’s subassemblies. When discrepancies are 
found, contact your GE Medical Systems 

Information Technologies

 Service 

Representative.

NOTE: 

Fab drawings are not contained in this manual.

Service Parts

WARNING

REPAIR TO THE FRU LEVEL - Field repairs are recommended 
to the field replaceable unit (FRU) only. Attempting a field repair 
on a PCB or a factory sealed component or assembly could 
jeopardize the safe and effective operation of the monitor.

Summary of Contents for Corometrics 250cx Series





























































































































































































































































Reviews:

No comments