GE CM6, Hardware Reference Manual

Page: 37 / 88

CompactPCI bus Connector J7001 and J7002
This interface is used for connection to a standard CPCI backplane.
Table 4: CPCI connectors J7001 and J7002
J7002 A B C D E F
22 GA4 GA3 GA2 GA1 GA0 GND
21 CLK6 GND COP_TDI SW_CFG# HW_WP# GND
20 CLK5 GND COP_TMS COP_TRST# COP_TCK GND
19 GND GND CKSTPIN# CKSTPOUT BFAIL# GND
18 PMCIO03/GPIO2 PMCIO02/GPIO1 PMCIO01/GPIO0 COP_TDO COP_SRST# GND
17 PMCIO05/GPIO4 PMCIO04/GPIO3 PRST# REQ6# GNT6# GND
16 PMCIO07/GPIO6 PMCIO06/GPIO5 DEG# GND COP_HRST# GND
15 PMCIO09/FKILL# PMCIO08/GPIO7 FAL# REQ5# GNT5# GND
14 PMCIO12 PMCIO11 PMCIO10 C1_RXD C1_RTS GND
13 PMCIO15 PMCIO14 PMCIO13 C1_TXD GND
12 PMCIO18 PMCIO17 PMCIO16 C1_CTS C2_RTS- GND
11 PMCIO21 PMCIO20 PMCIO19 GND
10 PMCIO24 PMCIO23 PMCIO22 LPB_DA- LPB_DB- GND
9 PMCIO26/52 PMCIO25 GND
8 PMCIO28 PMCIO27 C2_CTS- LPB_DC- LPB_DD- GND
7 PMCIO30/37 PMCIO29 GND
6 PMCIO32/39 PMCIO31 C2_TXD- LPA_DB- LPA_DA- GND
5 PMCIO38/44 PMCIO36/42 GND
4 VIO
b
PMCIO50 C2_RXD- LPA_DD- LPA_DC- GND
3 CLK4 GND GNT3# REQ4# GNT4# GND
2 CLK2 CLK3 SYSEN# GNT2# REQ3# GND
1 CLK1 GND REQ1# GNT1# REQ2# GND
J7001 A B C D E F
25 +5 V REQ64#
a
ENUM# +3.3 V +5 V GND
24 AD01 +5 V VIO
b
AD00 ACK64#
a
GND
23 +3.3 V AD04 AD03 +5 V AD02 GND
22 AD07 GND +3.3 V AD06 AD05 GND
21 +3.3 V AD09 AD08 M66EN C/BE0# GND
20 AD12 GND VIO
b
AD11 AD10 GND
19 +3.3 V AD15 AD14 GND AD13 GND
18 SERR# GND +3.3 V PAR C/BE1# GND
17 +3.3 V reserved reserved GND PERR# GND
16 DEVSEL# GND VIO
b
STOP# LOCK# GND
15 +3.3 V FRAME# IRDY# BDSEL# TRDY# GND
12-14 KEY KEY KEY KEY KEY KEY
11 AD18 AD17 AD16 GND C/BE2# GND
10 AD21 GND +3.3 V AD20 AD19 GND
9 C/BE3# IDSEL AD23 GND AD22 GND
8 AD26 GND VIO
b
AD25 AD24 GND
7 AD30 AD29 AD28 GND AD27 GND
6 REQ0# PCIPRESENT# +3.3 V CLK0 AD31 GND
5 reserved reserved RST# GND GNT0# GND
4 reserved GND VIO
b
reserved reserved GND
3 INTA# INTB# INTC# +5 V INTD# GND
2 TCK +5 V TMS TDO TDI GND
1 +5 V -12V TRST# +12V +5 V GND
a
These signals are not used on the CM6, but have a pull-up to VIO
b
The VIO signals are either 5 V or 3.3 V, depending on backplane
Reserved – Pin is reserved in the PICMG 2.0 specification. It is not used on the
CM6 board
GE Intelligent Platforms – CM6 Hardware Reference Manual, Fourth Edition Page 36