GE Centricity RA600 Service Manual Download Page 92 | Manualshive

Page: 92 / 278

background image

Hardware Installation

IST 013 Installing RAID Unit

Page 92

n

IST 013

Installing RAID Unit

Section 1: Introduction

This job card outlines how to install the RAID storage unit (Dell PowerVault 221S) with Centricity
RA600 (Dell 1400 platform) Work Group Server. The RAID unit is intended to be the primary short-
term image storage repository for the RA600 with Workgroup Server option.

For more detailed information on setting up the RAID unit, refe to the Dell Online Documentation
provided on CD-ROM with the Dell PowerVault 221S RAID unit. This information is also available on
the Dell website at www.support.dell.com/docs under Systems > PowerVault Storage > 220/221 S ~
Storage Systems > <language choice> > Installation & Service Guide > Service Information for
Technicians.

Section 2: Items Required

u

Dell 1400 PowerEdge computer with Color monitor, keyboard and mouse

u

Dell PowerVault 221S with two connecting SCSI cables

Section 3: Procedure

1.

Unpack and identify the system components:

n

Dell 1400 PowerEdge computer with keyboard, mouse and power cord

n

Color monitor with power cord and monitor connector cable

n

Dell PowerVault 221S RAID unit with two power cords and two SCSI-type cables.

When making cable connections, refer to the Dell connector illustrations that follow this procedure.

2.

Connect the monitor cable between the monitor and the video controller.

«
...
90
91
92
93
94
...
»

Summary of Contents for Centricity RA600























































































































































































































































































Reviews:

No comments

Related manuals for Centricity RA600

Brand: IEI Technology Pages: 131

Afolux LX Series

Brand: IEI Technology Pages: 131

Brand: Zotac Pages: 57

Brand: Asus Pages: 18

Brand: Asus Pages: 174

Brand: Asus Pages: 166

Brand: Siemens Nixdorf Pages: 26

MPC-2070 Series

Brand: Moxa Technologies Pages: 10

MPC-2101 Series

Brand: Moxa Technologies Pages: 51

DA-681-I-SP-XPE

Brand: Moxa Technologies Pages: 2

Brand: Moxa Technologies Pages: 73

Brand: Hyundai Pages: 80

Brand: Ergotron Pages: 20

XPC Barebone SH67H3

Brand: Shuttle Pages: 12

Brand: Peace Maker Technologies Pages: 2

Brand: Shuttle Pages: 35

Brand: Nexcom Pages: 58

Brand: Nexcom Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands