manualshive.com logo in svg

GE Centricity RA600, Service Manual

Share
Download
GE Centricity RA600 Service Manual Download Page 245

Troubleshooting

TSG 007 Display Centricity RA600 Application Logs

Page 245

n

TSG 007 Display Centricity RA600 Application Logs

Section 1: Introduction

This job card explains how to display the RA600 (RadWorks) workstation application logs. The 
workstation application log file (radworks.log) is an ASCII based log file located in the 

c:\ami_60\log

 

directory (assuming the RadWorks application is installed on the c:\ drive.

Section 2: GUI Based Procedure

1.

The text log files: Connect.LOG, Database.LOG, Print.LOG and RadWorks.LOG are located in 
the LOG subfolder of the AMI_60 folder. 
Navigate to this location using Windows explorer.

2.

Any ASCII text view program in windows can be used to display the log file, such as notepad, 
wordpad, etc.

Summary of Contents for Centricity RA600























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands