GE auisys cs2 User'S Reference Manual Download Page 67

Page: 67 / 268

Viewing alarm history

Use the

Alarm History

tab to view the list of the 12 most recent high

and medium priority alarms that occurred since the start of the case.
The alarm history clears at the start of a new case.

Select

Alarm Setup

Select the

Alarm History

tab.

The list of alarms shows in the window.

Select

Close

Setting alarm volume

Select

Alarm Setup

Select the

Configure

tab.

Set

Alarm Volume

to the desired value.

The alarm volume range is 1 to 5.

Select

Close

Setting apnea delay

Use the

Apnea Delay

setting to set the desired apnea time delay.

The apnea time delay is the amount of time that can pass without the
system detecting a measured breath before the apnea alarm occurs.

Select

Alarm Setup

Select the

Configure

tab.

Set

Apnea Delay

to the desired time.

•

The apnea time delay range is 10 to 30 seconds.

•

The apnea time settings are in 1 second increments.

Select

Close

Silencing leak audio alarms

Use the

Leak Audio

setting to silence audio alarms of small leaks.

Select

Alarm Setup

Select the

Configure

tab.

3 Operation

2067226-001

3-19

Summary of Contents for auisys cs2













































































































































































































































































Search results

Summary of Contents for auisys cs2

Reviews:

Related manuals for auisys cs2

Brands by name

Popular brands

GE auisys cs2, User'S Reference Manual

Search results

Summary of Contents for auisys cs2

Reviews:

Related manuals for auisys cs2

Brands by name

Popular brands