manualshive.com logo in svg

GE auisys cs2, User'S Reference Manual

The GE Auisys CS2 User's Reference Manual is a comprehensive guide packed with all the necessary information to effortlessly operate your device. This well-structured manual can be downloaded for free from our website, allowing you to access it anytime, anywhere. Enhance your user experience with our downloadable manual at manualshive.com.

Share
Download
background image

System information

System classification

This system is classified as follows:

•

Class I Equipment.

•

Type B Equipment.

•

Type BF Equipment (airway modules).

•

Ordinary Equipment.

•

Not for use with flammable anesthetics.

•

Continuous operation.

Device standards IEC 60601-1:2005

Devices used with this anesthesia system shall comply with the
following standards where applicable:

•

Breathing system and breathing system components ISO
80601-2-13.

•

Anesthetic gas scavenging systems ISO 80601-2-13

•

Anesthetic vapor delivery devices ISO 80601-2-13.

•

Anesthetic agent monitors ISO 80601-2-55.

•

Oxygen monitors ISO 80601-2-55.

•

Carbon dioxide monitors ISO 80601-2-55.

•

Exhaled volume monitors ISO 80601-2-13.

Device standards IEC 60601-1:1988

Devices used with this anesthesia system shall comply with the
following standards where applicable:

•

Breathing system and breathing system components ISO
8835-2.

•

Anesthetic gas scavenging systems ISO 8835-3

•

Anesthetic vapor delivery devices ISO 8835-4.

•

Anesthetic agent monitors ISO21647.

•

Oxygen monitors ISO 21647.

•

Carbon dioxide monitors ISO 21647.

•

Exhaled volume monitors IEC 60601-2-13.

Aisys CS²

1-14

2067226-001

Summary of Contents for auisys cs2













































































































































































































































































Reviews:

No comments

Related manuals for auisys cs2

NEC NEAX 2000 IVS System Manual preview
NEAX 2000 IVS
Brand: NEC Pages: 54
CAB 4712 Operator'S Manual preview
4712
Brand: CAB Pages: 13
CAB 4712 Assembly Instructions Manual preview
4712
Brand: CAB Pages: 30
CAB 5314 Operator'S Manual preview
5314
Brand: CAB Pages: 17
CAB 3014 Service Manual preview
3014
Brand: CAB Pages: 33
C. Crane Camping Equipment Instruction Manual preview
Camping Equipment
Brand: C. Crane Pages: 8
C-Pro Direct ADM Fittings Manual preview
ADM
Brand: C-Pro Direct Pages: 4
C-Pro Direct ADM Instructions For Use preview
ADM
Brand: C-Pro Direct Pages: 4
R.M. Young 32500 Quick Start Manual preview
32500
Brand: R.M. Young Pages: 10
GARANT SG1 Operation Manual preview
SG1
Brand: GARANT Pages: 239
p-light Midi Installation And Instructions For Use preview
Midi
Brand: p-light Pages: 36
Xtool A30 Pro Manual preview
A30 Pro
Brand: Xtool Pages: 51
H-TEC Education D201 Operating Instructions Manual preview
D201
Brand: H-TEC Education Pages: 16
H-TEC Education A129 Operating Instructions Manual preview
A129
Brand: H-TEC Education Pages: 12
Qlight SK Quick Start Manual preview
SK
Brand: Qlight Pages: 4
Tanco 1300 Series Operator'S Handbook Manual preview
1300 Series
Brand: Tanco Pages: 112
WE-EF LSP400 LED Series Installation And Maintenance Instructions Manual preview
LSP400 LED Series
Brand: WE-EF Pages: 6
Accurate Technology VALIANT Owner'S Manual preview
VALIANT
Brand: Accurate Technology Pages: 10

Brands by name

Popular brands

Load more brands