manualshive.com logo in svg

GE auisys cs2, User'S Reference Manual

The GE Auisys CS2 User's Reference Manual is a comprehensive guide packed with all the necessary information to effortlessly operate your device. This well-structured manual can be downloaded for free from our website, allowing you to access it anytime, anywhere. Enhance your user experience with our downloadable manual at manualshive.com.

Share
Download
background image

Changing a cassette during a case

1.

Push the Agent quick key.

2.

Set agent delivery to off.

3.

Turn the lock on the handle to the vertical position (Aladin2
cassettes only).

4.

Remove cassette from the active bay.

•

Store the cassette in the cassette storage bay if it will not be
used.

•

Fill the cassette following the appropriate filling procedure if
the cassette requires filling.

5.

Install a cassette following the Installing a cassette procedure.
A tone sounds.
The agent setting in the quick key area flashes.
If cassette of same agent type is installed during a case, the last
agent setting used shows the agent quick key.

6.

Change or confirm the agent setting.

7.

To confirm the agent setting:

•

Push the ComWheel to confirm the setting.

•

Push the Agent quick key to confirm the setting.

If the setting is not confirmed within 30 seconds, the agent
delivery is set to off.

8.

To change an agent setting:

•

Turn the ComWheel to the desired setting.

•

Push the ComWheel or push the quick key to confirm the
setting.

Aisys CS²

13-6

2067226-001

Summary of Contents for auisys cs2













































































































































































































































































Reviews:

No comments

Related manuals for auisys cs2

Navman 2 Installation And Operation Manual preview
2
Brand: Navman Pages: 17
Eclipse Combustion 6500 Instruction Manual preview
6500
Brand: Eclipse Combustion Pages: 46
Bard Duet Instructions For Use preview
Duet
Brand: Bard Pages: 2
SAMCHULLY SD Instruction Manual preview
SD
Brand: SAMCHULLY Pages: 48
AAON RQ SERIES Manual preview
RQ SERIES
Brand: AAON Pages: 36
Hammer FR Series Operation And Maintenance Manual preview
FR Series
Brand: Hammer Pages: 42
MAGIC FX CO2JET II User And Installation Manual preview
CO2JET II
Brand: MAGIC FX Pages: 25
TC Electronic PolyTune Clip Manual Manual preview
PolyTune Clip
Brand: TC Electronic Pages: 14
Access BIMINI Assembly Instructions Manual preview
BIMINI
Brand: Access Pages: 7
A.HABERKORN KS 45 Instructions For Use And Test Manual preview
KS 45
Brand: A.HABERKORN Pages: 28
Garmin FUSION APOLLO MS-WB675 Installation Instructions Manual preview
FUSION APOLLO MS-WB675
Brand: Garmin Pages: 18
Rapid Shape RS wash Quick Start Manual preview
RS wash
Brand: Rapid Shape Pages: 12
Hanskamp MultiFill 003-561-005 Installation And Operating Instructions Manual preview
MultiFill 003-561-005
Brand: Hanskamp Pages: 20
Össur L-331002 Instructions For Use Manual preview
L-331002
Brand: Össur Pages: 16
Össur Exoform Dorsal Night Splint Instructions For Use Manual preview
Exoform Dorsal Night Splint
Brand: Össur Pages: 34
Magicfx CO2 Jet User And Installation Manual preview
CO2 Jet
Brand: Magicfx Pages: 25
Valmont Structures Mitigator TR1 Installation Instructions Manual preview
Mitigator TR1
Brand: Valmont Structures Pages: 8
Gilson F123600 Quick Manual preview
F123600
Brand: Gilson Pages: 8

Brands by name

Popular brands

Load more brands