GE auisys cs2 User'S Reference Manual Download Page 136 | Manualshive

Page: 136 / 268

background image

Moving and transporting the system

The system may overbalance or tip if tilted more than 10

degrees.

Do not exceed specified load ratings when mounting

equipment on the top of the machine or on any of the

side rails.

Attaching equipment to the top of the machine

" and

Specifications and theory of operation

" for system load ratings.

Before transporting or moving the system, fold all display arms into
the system and put the flip-up shelf in the down position. Tighten the
horizontal-positioning lock on the display arm. When using the brake
on an incline, be sure to lock the brake with the machine facing down
the slope.

WARNING

•

Aisys CS²

8-4

2067226-001

«
...
134
135
136
137
138
...
»

Summary of Contents for auisys cs2













































































































































































































































































Reviews:

No comments

Related manuals for auisys cs2

Brand: JB-Lighting Pages: 40

Brand: Eaton Pages: 16

Brand: Eaton Pages: 6

Brand: Ecco Pages: 17

ENET-232 Series

Brand: National Instruments Pages: 105

Brand: Safety 1st Pages: 4

Brand: Safety Engineering Pages: 5

Brand: Fagor Pages: 12

Brand: Baltic Pages: 68

Brand: H&S Pages: 76

Team Agile Color Tune TM16-0

Brand: GRAU Pages: 24

Brand: Ground Fault Systems Pages: 26

Brand: Oromed Pages: 64

Brand: Osprey Pages: 12

DIAGNOdent pen 2190

Brand: KaVo Pages: 2

Brand: PFM Medical Pages: 26

Pivot track filler

Brand: Norwest Pages: 16

Brand: ResMed Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands