GE AKTAprocess Operating Instructions Manual Download Page 76

Page: 76 / 180

Meters and sensors

The following table lists the meters and sensors that are shown in the flow chart.

Note

Function

Tag

Movable

Buffer inlet air sensor

AE-151

Final check that no air enters the column

Pre-column air sensor

AE-152

Post-column pH-meter

AT-121

Peak detection

Post-column UV-meter

AT-131

Also includes a temperature meter

Pre-column conductivity meter

CE/TE-101

Peak detection and CIP-control, also includes
a temperature meter

Post-column conductivity
meter

CE/TE-102

Measures the total system flow

System flow meter

FT-141

Air trap high level meter

LEH-167

Air trap low level meter

LEL-166

Option

Pre-filter pressure meter

PT-111

Guards the column from over pressure,
detects clogged column

Pre-column pressure meter

PT-112

Part of sample pump option

Sample pump pressure meter

PT-114

part of PCV option

PCV pressure meter, A inlets

PT-115

part of PCV option

PCV pressure meter, B inlets

PT-116

ÄKTAprocess Operating Instructions 29-0252-49 AA

3 System description

3.5 Flowchart

Summary of Contents for AKTAprocess





















































































































































































Search results

Summary of Contents for AKTAprocess

Reviews:

Brands by name

Popular brands

GE AKTAprocess, Operating Instructions Manual

Search results

Summary of Contents for AKTAprocess

Reviews:

Brands by name

Popular brands