manualshive.com logo in svg

GE AKTAprocess, Operating Instructions Manual

Share
Download
GE AKTAprocess Operating Instructions Manual Download Page 124

5.2

Perform a run

Precautions

WARNING

Cabinet doors. During operation, all doors must always be closed
and locked.

WARNING

Use a harmless fluid in the beginning of the process. This will make
it possible to detect leakage with minimized consequences and
the risk for potential leakage of hazardous fluids is avoided.

CAUTION

Use ear protection whenever working close to the system in
operation.

NOTICE

Excessive temperatures may damage the equipment. Do not run
the system at higher temperatures than the specified maximum
operation temperature as stated on the system label.

NOTICE

Operator console

•

Do not use the operator console to push or drag the system

•

Do not lean on the console

The console arm is only designed to support the weight of the
operator console.

124

ÄKTAprocess Operating Instructions 29-0252-49 AA

5 Operation

5.2 Perform a run

Summary of Contents for AKTAprocess





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands