manualshive.com logo in svg

GE AKTA ready, Operating Instructions Manual

Share
Download
GE AKTA ready Operating Instructions Manual Download Page 48

3.4

Equipment

Pinch valves

Pinch valves are used to control the path of the
liquid flow through the system. There are 19 pinch
valves in total. The valves have manually operated
safety locks keeping the tubing in place and pre-
venting the valves from accidentally closing during
flow kit installation.

WARNING

Never put fingers or any objects other than the intended tubing in
to the pinch valve opening.

Default position

Valves

Closed

Inlet valves, XV-001 to XV-006

Inline

Air trap valves, XV-021 to XV-023

Bypass

Column valves, XV-031 to XV-033

Closed

Outlet valves, XV-051 to XV-056

Closed

Air Vent Valve, HV-301

During pause, the air trap valves will remain in the same position as during the run. The
user can change this by setting the air trap valves to inline during pause, in the System
Settings in UNICORN.

48

ÄKTA ready Operating Instructions 28960345 AD

3 System description

3.4 Equipment

Summary of Contents for AKTA ready




































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands