24
Advent Commercial Fire System
Enable Auto Force Arming
xx092
(Partitions-Arming)
(Default = on) If on, any protesting zone(s) will be bypassed upon
arming. If off, then the partition/area will not arm if
any
zone(s)
are protesting.
To turn Enable Auto Force Arming On/Off:
Once the item number has been entered, enter
1
to turn the
setting on or
0
to turn it off. Press
ƒ
to apply the new setting.
Enable Quick Arming
xx093
(Partitions-Arming)
(Default = on) If on, anyone can arm the panel and increase
arming levels without an access code. A valid access code is still
required to decrease arming levels or disarm the system. Quick
arm works as follows:
Level 3 to 5 = no code
Level 3 to 4 = code
Level 4 to 3 = not code
Level 5 to 3 = code
Level 1 to 2 = no code
Level 1 to 3 = no code
Level 1 to 4 = no code
Level 1 to 5 = no code
To turn Enable Quick Arming On/Off:
Once the item number has been entered, enter
1
to turn the
setting on or
0
to turn it off. Press
ƒ
to apply the new setting.
Exterior Arming Verification
xx097
(Partitions-Arming)
(Default = off) If on, exterior sirens will produce arming
verification sounds notifying users that the system was armed.
Note
In order for this setting to work,
Audible Verification at
Close Reports
setting (xx098) must be set to “on.”
To turn Exterior Arming Verification On/Off:
Once the item number has been entered, enter
1
to turn the
setting on or
0
to turn it off. Press
ƒ
to apply the new setting.
Number of Zones that can be Bypass
xx017
(Partitions-Arming)
(Default = 250) Select the number of zones that may be bypassed
at once. See Table B.1 on page 87 for information on which zone
types may be bypassed.
To program the Number of Zones that can be
Bypassed:
Once the item number has been entered, enter the number of
zones that may be bypassed at once (0–250). Press
ƒ
to apply the
new setting.
Enable Automatic Unbypass
xx096
(Partitions-Arming)
(Default = off) If on, an indirectly bypassed zone will
automatically be unbypassed once the door, window, etc., has
been closed for 30 seconds. This setting only applies to delayed
zones.
To turn Enable Automatic Unbypass On/Off:
Once the item number has been entered, enter
1
to turn the
setting on or
0
to turn it off. Press
ƒ
to apply the new setting.
Enable Swinger Bypass
xx095
(Partitions-Arming)
(Default = on) If on, a zone that exceeds the set swing count
(xx021) during a single arming period will automatically be
bypassed. Changing the arming level restores all automatically
bypassed zones and resets the swing count.
To turn Enable Swinger Bypass On/Off:
Once the item number has been entered, enter
1
to turn the
setting on or
0
to turn it off. Press
ƒ
to apply the new setting.
Swing Count (Auto Bypass Trips)
xx021
(Partitions-Arming)
(Default = 3) Select the maximum number of report attempts that
one zone can generate during a single arming period before the
panel automatically bypasses that zone.
All automatically bypassed zones, and the swing count, will reset
if the system clock reaches midnight or an arming level change
occurs.
To set the Swing Count:
Once the item number has been entered, enter the desired swing
count (1–8) and press
ƒ
.
Standard Entry Delay
xx003
(Partitions-Arming)
(Default = 32 seconds) Enter the length of the standard entry
delay (in seconds). This is the number of seconds the user has to
disarm the system after tripping a standard delay zone. If the
system isn’t disarmed within this time period an alarm is
generated.
To set the Standard Entry Delay:
Once the item number has been entered, enter the number of
seconds (24–120) users will have to disarm the system. Press
ƒ
to apply the new setting.
Summary of Contents for Advent
Page 56: ...54 Advent Commercial Fire System ...
Page 88: ...86 Advent Commercial Fire System ...
Page 110: ...108 Advent Commercial Fire System ...
