GE Multilin C60 UR series, Instruction Manual

Page: 48 / 544

2-16 C60 Breaker Protection System GE Multilin
2.2 SPECIFICATIONS 2 PRODUCT DESCRIPTION
2
2.2.9 INTER-RELAY COMMUNICATIONS
SHIELDED TWISTED-PAIR INTERFACE OPTIONS
RS422 distance is based on transmitter power
and does not take into consideration the clock
source provided by the user.
LINK POWER BUDGET
These power budgets are calculated from the
manufacturer’s worst-case transmitter power
and worst case receiver sensitivity.
The power budgets for the 1300nm ELED are cal-
culated from the manufacturer's transmitter
power and receiver sensitivity at ambient temper-
ature. At extreme temperatures these values will
deviate based on component tolerance. On aver-
age, the output power will decrease as the tem-
perature is increased by a factor 1dB / 5°C.
MAXIMUM OPTICAL INPUT POWER
TYPICAL LINK DISTANCE
Compensated difference in transmitting and receiving (channel
asymmetry) channel delays using GPS satellite clock: 10 ms
2.2.10 ENVIRONMENTAL
OPERATING TEMPERATURES
Cold: IEC 60068-2-1, 16 h at –40°C
Dry heat: IEC 60068-2-2, 16 h at +85°C
Storage temperature: –40 to +85°C
UL/CSA/CE safety rating:–40 to +60°C
The LCD contrast may be impaired at temperatures less
than –20°C.
OTHER
Humidity (non-condensing): IEC 60068-2-30, 95%, Variant 1, 6
days
Altitude: Up to 2000 m
Installation category: II
Pollution degree: 2
INTERFACE TYPE TYPICAL DISTANCE
RS422 1200 m
G.703 100 m
EMITTER,
FIBER TYPE TRANSMIT
POWER
RECEIVED
SENSITIVITY
POWER
BUDGET
820 nm LED,
Multimode –20 dBm –30 dBm 10 dB
1300 nm LED,
Multimode –21 dBm –30 dBm 9 dB
1300 nm ELED,
Singlemode –23 dBm –32 dBm 9 dB
1300 nm Laser,
Singlemode –1 dBm –30 dBm 29 dB
1550 nm Laser,
Singlemode +5 dBm –30 dBm 35 dB
EMITTER, FIBER TYPE MAX. OPTICAL
INPUT POWER
820 nm LED, Multimode –7.6 dBm
1300 nm LED, Multimode –11 dBm
1300 nm ELED, Singlemode –14 dBm
1300 nm Laser, Singlemode –14 dBm
1550 nm Laser, Singlemode –14 dBm
NOTE
NOTE
NOTE
EMITTER TYPE CABLE
TYPE CONNECTOR
TYPE
TYPICAL
DISTANCE
820 nm LED,
multimode 62.5/125
μ
m ST 1.65 km
1300 nm LED,
multimode 62.5/125
μ
m ST 3.8 km
1300 nm ELED,
single mode 9/125
μ
m ST 11.4 km
1300 nm Laser,
single mode 9/125
μ
m ST 64 km
1550 nm Laser,
single-mode 9/125
μ
m ST 105 km
Typical distances listed are based on the fol-
lowing assumptions for system loss. As
actual losses will vary from one installation to
another, the distance covered by your system
may vary.
CONNECTOR LOSSES (TOTAL OF BOTH ENDS)
ST connector 2 dB
FIBER LOSSES
820 nm multimode 3 dB/km
1300 nm multimode 1 dB/km
1300 nm singlemode 0.35 dB/km
1550 nm singlemode 0.25 dB/km
Splice losses: One splice every 2 km,
at 0.05 dB loss per splice.
SYSTEM MARGIN
3 dB additional loss added to calculations to compensate for
all other losses.
NOTE
NOTE