GE Multilin 469 Instruction Manual Download | Manualshive

Page: 228 / 338

background image

5–86

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER 5: SETTINGS

5.12 S11 Monitoring

5.12.1 Trip Counter

PATH: SETTINGS

ZV

S11 MONITORING

Z

TRIP COUNTER

When the Trip Counter Limit is reached, an alarm will occur. The trip counter must be
cleared or the alarm level raised and the reset key must be pressed (if the alarm was
latched) to reset the alarm.

For example, it might be useful to set a Trip Counter alarm at 100 so that if 100 trips occur,
the resulting alarm prompts the operator or supervisor to investigate the type of trips that
occurred. A breakdown of trips by type may be found on

A3 MAINTENANCE\TRIP COUNTERS

.

If a trend is detected, it would warrant further investigation.

5.12.2 Starter Failure

PATH: SETTINGS

ZV

S11 MONITORING ELEMENTS

ZV

STARTER FAILURE

If the

STARTER FAILURE ALARM

is set to “Latched” or “Unlatched”, then the Starter Status

input and motor current are monitored when the 469 initiates a trip. If the starter status
contacts do not change state or motor current does not drop to zero after the
programmed time delay, an alarm occurs. The time delay should be slightly longer than

TRIP

[

TRIP COUNTER

ALARM: Off

Range: Off, Latched, Unlatched

MESSAGE

ASSIGN ALARM

RELAYS:

Range: Alarm, Alarm & Auxiliary2,

Alarm & Aux2 & Aux3, Alarm &
Auxiliary3, Auxiliary2, Aux2 &
Aux3, Auxiliary3

MESSAGE

TRIP COUNTER

ALARM

Range: 1 to 50000 Trips in steps of 1

MESSAGE

TRIP COUNTER

ALARM

Range: On, Off

STARTER

[

STARTER FAILURE

ALARM: Off

Range: Off, Latched, Unlatched

MESSAGE

STARTER TYPE:

Breaker

Range: Breaker, Contactor

MESSAGE

ASSIGN ALARM

RELAYS:

Range: Alarm, Alarm & Auxiliary2,

Alarm & Aux2 & Aux3,
Alarm & Auxiliary3, Auxiliary2,
Aux2 & Aux3, Auxiliary3

MESSAGE

STARTER FAILURE

DELAY: 100 ms

Range: 10 to 1000 ms in steps of 10

MESSAGE

SUPERVISION OF

TRIP

Range: Disabled, 52 Closed, 52 Open/

Closed

MESSAGE

STARTER FAILURE

ALARM EVENTS: Off

Range: On, Off

«
...
226
227
228
229
230
...
»

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Related manuals for 469

Brand: ABB Pages: 20

Brand: Eaton Pages: 2

Brand: ZIEHL Pages: 28

Brand: Siemens Pages: 6

Brand: Siemens Pages: 8

Brand: Siemens Pages: 8

Brand: Siemens Pages: 4

Brand: Siemens Pages: 4

BD2-AK03X/FS Series

Brand: Siemens Pages: 8

Brand: CAMDEN Pages: 15

Brand: ABB Pages: 16

Brand: ABB Pages: 2

Ex STM 295 3G/D Series

Brand: steute Pages: 24

Brand: FANOX Pages: 7

Brand: FANOX Pages: 17

WireLink EasyTouch II ScenePoint SR1 Series

Brand: Vantage Hearth Pages: 4

G70D B7A Series

Brand: Omron Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands