manualshive.com logo in svg

GE Multilin 469, Instruction Manual

Share
Download
GE Multilin 469 Instruction Manual Download Page 172

5–30

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER 5: SETTINGS

Digital Counter

PATH: SETTINGS 

ZV

 S3 DIGITAL INPUTS 

ZV

 ASSIGNABLE INPUT 1(4)

These settings apply only if the 

INPUT 1(4) FUNCTION

 is “Digital Counter”.

Once the Digital Counter function is chosen for one of the assignable digital inputs, the 
settings messages shown here will follow the assignment message. Each closure of the 
switch will be counted, by either incrementing or decrementing the counter value. An 
alarm may be configured when a certain count is reached. The counter value may be 
viewed in the 

A4 MAINTENANCE 

ZV

 GENERAL COUNTERS 

ZV

 DIGITAL COUNTER

 actual 

value.

To initialize the counter, program the counter value here and then change the 

S1 469 SETUP 

ZV

 CLEAR DATA 

ZV

 PRESET DIGITAL COUNTER

 settings to “Yes”.

For example, a capacitive proximity probe may be used to sense non-magnetic units that 
are passing by on a conveyor, glass bottles for instance. The probe could be powered from 
the +24 V from the input switch power supply. The NPN transistor output could be taken to 
one of the assignable digital inputs configured as a counter.

Tachometer

PATH: SETTINGS 

ZV

 S3 DIGITAL INPUTS 

ZV

 ASSIGNABLE INPUT 1(4)

„

 

ASSIGNABLE

[

INPUT 1 FUNCTION:

Digital Counter

Range: See above

MESSAGE

COUNTER UNITS:

Units

Range: 6 alphanumeric characters

MESSAGE

COUNTER PRESET

VALUE: 0

Range: 0 to 1000000000 in steps of 1

MESSAGE

COUNTER TYPE:

Increment

Range: Increment, Decrement

MESSAGE

COUNTER

ALARM: Off

Range: Off, Latched, Unlatched

MESSAGE

ASSIGN ALARM 

RELAYS:

Range: Alarm, Alarm & Auxiliary2, 

Alarm & Aux2 & Aux3, Alarm & 
Auxiliary3, Auxiliary2, Aux2 & 
Aux3, Auxiliary3

MESSAGE

COUNTER ALARM

LEVEL: 100

Range: 0 to 1000000000 in steps of 1

MESSAGE

COUNTER ALARM

PICKUP: Over

Range: Over, Under

MESSAGE

COUNTER ALARM

EVENTS: Off

Range: On, Off

„

 

ASSIGNABLE

[

INPUT 1 FUNCTION:

Tachometer

Range: See above

MESSAGE

RATED SPEED:

3600 RPM

Range: 100 to 7200 RPM in steps of 1

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands