manualshive.com logo in svg

GE Multilin 469, Instruction Manual

Share
Download
GE Multilin 469 Instruction Manual Download Page 158

5–16

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER 5: SETTINGS

•

CLEAR ANALOG I/P MIN/MAX: 

The minimum and maximum analog input values are 

stored for each analog input. These minimum and maximum values may be cleared at 
any time.

•

CLEAR TRIP COUNTERS: 

There are counters for each possible type of trip. This 

command clears these counters.

•

PRESET DIGITAL COUNTER: 

When one of the assignable Digital Inputs is configured as 

“Counter”, this command presets the counter. If the counter is an incrementing type, 
setting the preset value to “0” effectively resets the counter.

•

CLEAR EVENT RECORDER: 

The event recorder saves the last 256 events, 

automatically overwriting the oldest event. If desired, this command can clear all 
events to prevent confusion with old information.

5.2.8

Installation

PATH: SETTINGS 

Z

 S1 469 SETUP 

ZV

 INSTALLATION

These commands clear various informative and historical data when the 469 is first 
applied on a new installation.

•

RESET MOTOR INFORMATION: 

Counters for number of motor starts and emergency 

restarts can be viewed in actual values. The 469 also learns various motor 
characteristics through motor operation. These learned parameters include 
acceleration time, starting current, and starting thermal capacity. Total motor running 
hours may also be viewed in actual values. On a new installation or if new equipment 
is installed, all this information can be reset with this settings.

•

RESET STARTER INFORMATION: 

The total number of starter operations can be viewed 

in actual values. Use this settings to clear this counter on a new installation or if 
maintenance work is done on the breaker or contactor.

„

 

INSTALLATION

[

RESET MOTOR

INFORMATION: No

Range: No, Yes

MESSAGE

RESET STARTER

INFORMATION: No

Range: No, Yes

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands