manualshive.com logo in svg

GE Medical Systems MAC 1200, Operator'S Manual, Page: 137 / 180

Share
Download
GE Medical Systems MAC 1200 Operator'S Manual Download Page 137

Revision B

MAC 1200

9-31

2012250-022

System Setup: Direct ECG Transmission

Direct ECG Transmission

„

Select the 12 Lead mode and press 

.

„

Press 

 to display the configuration menu for the 12 Lead mode.

„

Use the cursor keys to position the bar cursor on Manual copy to 

HOST and confirm the selection with 

 ([HOST]).

„

Press 

 to clear the configuration menu.

„

Use the cursor keys to position the bar cursor on Communication and 

confirm the selection with 

.

„

Select the same baud rate as at the receiving modem (2400, 4800, 
9600, 19200, 38400, 57600).

Selecting the Communication Protocol

This adjustment is only necessary with MAC 1200 units, because this 
device can send data to CardioSys/CardioSoft or to the MUSE system.

1.

Using the cursor keys, position the bar cursor on Protocol.

2.

Select the protocol A5 if you will send data to CardioSys/CardioSoft 
system or select CSI to send data to MUSE system. 

3.

Use the cursor keys to position the bar cursor on Modem, none and 

confirm the selection with 

.

copy

Summary of Contents for MAC 1200





















































































































































































Reviews:

No comments