manualshive.com logo in svg

GE Medical Systems MAC 1200, Operator'S Manual, Page: 131 / 180

Share
Download
GE Medical Systems MAC 1200 Operator'S Manual Download Page 131

Revision B

MAC 1200

9-25

2012250-022

System Setup: Communication

Communication

Baud Rate (PC)

Transmission rate for the selected protocol. We recommend the default 
setting of [19200 baud].

Protocol

The recorder offers two communication protocols: “A5” and “CSI”. 

With the “A5” protocol, the 10-second resting ECG can be transmitted to 
CardioSys and CardioSoft.

The CSI protocol supports the transfer of resting ECGs from the 
electrocardiograph to a MUSE CV system. 

Modem

Select the modem type. Choose among the standard modems MultiTech 
(MT 19.2, 56k), Elsa 14.4, 28.8, 33.6, 56k and a user-defined modem.

When using one of the standard modems, enter the following:

„

The dial mode (pulse or tone, depending on your telephone network).

„

The telephone number (20 digits maximum).

„

The number to access the public telephone network (e.g. “0”).

For a user-defined modem, enter the following:

„

The telephone number (20 digits maximum).

„

The init string (20 characters maximum). (See modem operator's 
manual.)

„

The dial string (20 characters maximum). (See modem operator's 
manual.)

„

The hangup mode (20 characters maximum). (See modem operator's 
manual.)

Summary of Contents for MAC 1200





















































































































































































Reviews:

No comments