manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

Share
Download
GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 203

 Disassembly and reassembly

  195

2062973-003

12.2.11 Detaching the front unit assembly from the mid-frame assembly

Disassemble first:
a.

12.2.6. Detaching the front unit and mid-frame assembly from the rear unit assembly

1. Remove the screw cover plate at the bottom 

of the front panel.

2. Remove the two screws (T10) holding the front 

unit assembly to the mid-frame assembly.

Keep the front unit and mid-frame assembly on 
the table the display facing down. Protect the 
touchscreen sensor from any scratches and dust.
3. Detach user interface and touchscreen cables 

from the DC/DC board.

4. Release the four snaps - two on each side - 

that mount the front unit assembly to the 
mid-frame assembly.

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands