manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

Share
Download
GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 20

CARESCAPE Monitor B450

 12

2062973-003

3.2.4 Acquisition modules

The patient monitor includes standard docking for the following multiparameter hemodynamic 
modules: PSM and PDM. 

The integrated E-module slot can occupy one single-width E-module at a time.

Refer to the patient monitor’s supplemental information manual for a list of compatible 
acquisition devices and to the patient monitor’s user’s manual for a list of parameters each 
module measures.

3.2.5 CARESCAPE Network MC or S/5 Network

The patient monitor is compatible both with the CARESCAPE Network MC and the S/5 Network 
infrastructures. The optional WLAN support enables wireless network communication using 
IEEE 802.11a/b/g.
Refer to the patient monitor’s supplemental information manual for a list of compatible 
CARESCAPE and S/5 Network devices.

PSM

PDM

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands