manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

Share
Download
GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 116

CARESCAPE Monitor B450

 108

2062973-003

8.2.8 Patient (source) leakage current tests

This procedure measures the leakage current from an applied part connector of the device to 
ground. 

Perform the test in Normal Condition (NC) and in two different Single Fault Conditions (SFC): 
1) earth open and 2) one of the supply conductors open at a time. 

 

Perform test with normal and reverse polarity. 
NOTE: Refer to the instructions delivered with the safety analyzer to perform this test.

NOTE: *The measuring device (MD) represents the network and voltage measuring instrument 
and its frequency characters according to IEC 60601-1.
NOTE: Perform this test for all the connected parameter modules and patient connectors 
specified in 

Table 1

.

1.

Configure the safety analyzer as follows (NC):

−

Polarity: NORMAL

−

Neutral: CLOSED

−

Earth (GND): CLOSED

2.

Power on the device under test.

3.

Read and record the current leakage indicated on the safety tester.

4.

Configure the safety analyzer as follows (SFC):

−

Polarity: NORMAL

−

Neutral: OPEN

−

Earth (GND): CLOSED

5.

Read and record the current leakage indicated on the safety tester.

6.

Configure the safety analyzer as follows (SFC):

−

Polarity: NORMAL

−

Neutral: CLOSED

−

Earth (GND): OPEN

7.

Read and record the current leakage indicated on the safety tester.

8.

Configure the safety analyzer as follows (SFC):

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands