manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

Share
Download
GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 10

CARESCAPE Monitor B450

 2

2062973-003

1.3.1 Product naming conventions

In this manual, the CARESCAPE Monitor B450 is referred to as the patient monitor.
The following naming conventions are used to refer to different modules and module 
categories:

−

PDM: Patient Data Module

−

PSM: Patient Side Module: E-PSM, E-PSMP, E-PSMW and E-PSMPW.

−

E-modules: all modules with prefix E-.

−

Cardiac output and SvO

2

 E-modules: E-COP and E-COPSv.

−

Pressure and Temperature E-modules: E-P, E-PP and E-PT.

−

Continuous Cardiac Output Module: E-PiCCO.

−

CARESCAPE respiratory modules: E-sCAiOV family.

−

Single-width airway module: E-miniC

−

Specialty E-modules: E-NMT, E-EEG, E-BIS and E-ENTROPY

−

SpO

2

 E-modules: E-NSATX, E-MASIMO

The CARESCAPE Network MC is referred as MC network and the CARESCAPE Network IX as 
IX network.

Menu naming varies within software packages:

−

Admit/ Discharge

 is also used in this manual for 

Start/End

 case

 menu (in OR and PACU 

software).

1.4 Illustrations and names

This manual uses illustrations as examples only. Illustrations in this manual may not 
necessarily reflect all system settings, features, configurations, or displayed data. 
Names of persons, institutions, and places and related information are fictitious; any similarity 
to actual persons, entities, or places is purely coincidental.

1.5 Ordering manuals

A paper copy of this manual will be provided upon request. Contact your local GE 
representative and request the part number on the first page of the manual.

1.6 Related documents 

−

the patient monitor’s user’s manual

−

the patient monitor’s supplemental information manual

−

Module Frames and Modules Technical Manual

−

CARESCAPE Modular Monitors Software Installation Instructions

−

CARESCAPE Network Configuration Guide

−

CARESCAPE Wireless Network Configuration Guide

−

CARESCAPE Modular Monitors Mounting Solutions

−

Unity Network Interface Device (ID) Operator's Manual

−

iCentral and iCentral Client Technical Reference Manual

−

S/5 Network Installation Guide

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands