General Procedures and Information
07/23/2020
GBC StreamWire
6-44
GP 6.5.3
Check M6 and M7
Locate Motors M6 and M7:
•
Raise the top cover and lower bypass
•
Insert a cheater into the upper bypass panel interlock switch
•
M6 is located on the front tapper assembly. Refer to PL 5.17
•
M7 is located on the rear tapper assembly. Refer to PL 5.18
•
Alternatively, you can do
Tappers just once.
1. Do
to check that the corresponding
motors turn when activated.
The Tapper linkage turns when Motor is activated.
Yes
- Return to the RTP that directed you here
No
- Identify the malfunctioning Motor(s) and go to Step 2.
2. Make sure the motor wire is connected securely at the header and at
the Main Control Board (PL 5.27). Do REP 1.5 to remove the Rear
Cover to gain access to the connector at the Control Board. Refer to
All the connectors are securely connected.
Yes
- Go to Step 3
No
- Make the connection and resume operation
3. Check the tightness of the set screw of the hub on the DC motor
shaft.
Set screw is secured tightly
Yes
- Go to Step 4
No
- Tighten the loose set screw and resume operation
4. Check that the cable(s) connecting the Motor to the Main Control
Board are intact. Refer to the motor cables table to identify the
appropriate cable part numbers,
The cables look okay
Yes
- Go to Step 5
No
- Replace the faulty cable and resume normal operation
firmware for the eWire
This clears the fault
Yes
- Resume normal operation
No
- Go to Step 6
6. Replace the faulty motor. Refer to REP 7.2, Tapper Motor
Replacement M6 and M7.
This clears the fault
Yes
- Resume normal operation
No
- Go to Step 7
7. Replace the cables from the motor to the Main Control Board. Refer
to Section 7, Wiring and GP 6.24 to identify the correct cable part
numbers.
This clears the fault
Yes
- Resume normal operation
No
- Go to Step 8
8. Replace Main Control Board A (REP 11.1)
This clears the fault
Yes
- Resume normal operation
No
- Escalate to second level
Summary of Contents for StreamWire
