manualshive.com logo in svg

Gateway E-842R, User Manual

Share
Download
Gateway E-842R User Manual Download Page 28

CHAPTER 3: Getting Started

www.gateway.com

22

Enclosure Temperature icon

The enclosure temperature icon is displayed just above the rear 
enclosure icon and indicates the status of the enclosure 
temperature.

■

Normal - This green icon indicates that the temperature is 
normal. 

■

Warning - This yellow icon indicates that the enclosure 
temperature is approaching the established threshold.

■

Failed - This red icon indicates that the enclosure temperature 
has reached or exceeded the enclosure temperature threshold. 
(If the fans are operating normally and the air flow temperature 
seems normal, the temperature sensor may be faulty.

■

Missing - This icon indicates that the information from the 
SES/SAF-TE regarding the sensors is invalid or missing.

Enclosure icon
RAID Storage Solution

Enclosure icons are displayed at the bottom of the Main window 
and change shades according to enclosures state, as well as, the 
state of the individual components. The enclosures are labeled 
above each front view to aid with identifying them in a multiple 
enclosure environment.

■

Normal - All components are operating normally.

■

Communication Error- The SES process  has lost 
communication with the enclosure (the icon becomes grey or 
dim) or you have disabled 

Enclosure Support

 in the Controller 

Advanced Settings.

Enclosure Section

Description and Condition

Normal

Warning

Failed

Missing

Summary of Contents for E-842R





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands