manualshive.com logo in svg

Gateway E-842R, User Manual

Share
Download
Gateway E-842R User Manual Download Page 142

APPENDIX B: Event Logs

www.gateway.com

136

Failed Drives Codes

The controller maintains a list of failed drives. Drives are listed in the following 
format:

Failed Drive:xx SN: yy yy yy yy yy yy

Reason Code

The reason code may be one of the following:

The Server performed a CGI 
request but an internal error 
prevented the Server from 
returning the results.

Error
[0x304 (772)]

The request was 
performed but the 
Server encountered an 
error that prevented 
completion.

Retry request.
Quit StorView and all 
connections accessing 
this StorView Server, 
wait 1 minute, then 
restart them.
Restart the system.

The Server performed a CGI 
request but the shared 
memory needed to return 
the results could not be 
created.

Error
[0x305 (773)]

The Server completed 
the request and 
attempted to create 
shared memory to 
send the results back 
to the Server CGI. The 
attempt failed.

Retry request.
Quit StorView and all 
connections accessing 
this StorView Server, 
wait 1 minute, then 
restart them.
Restart the system.

The Server failed to 
complete a CGI request 
before its allowed time 
expired.

Error
[0x306 (774)]

The Server completed 
the request, but by the 
time it was done the 
Server CGI gave up.

Retry request.
Quit StorView and all 
connections accessing 
this StorView Server, 
wait 1 minute, then 
restart them.
Restart the system.

The Server CGI script was 
unable to return CGI 
request results to the GUI.

Error
[0x307 (775)]

The Server passed the 
completed request to 
the Server CGI, but for 
some reason the 
request was not 
completed correctly by 
the Server CGI script.

Retry request.
Quit StorView and all 
connections accessing 
this StorView Server, 
wait 1 minute, then 
restart them.
Restart the system.

Start up is complete.

Information
[0xA01 
(2561)]

The controller module 
has been loaded by the 
StorView Server.

No action necessary.

Several failures 
encountered while trying to 
communicate with the RAID 
controller.

Error
[0xA03 
(2563)]

Several commands 
have been sent 
through a known good 
path, but they have 
failed.

Make sure that the 
paths and hardware are 
operational.

Successful communication 
with controller after several 
failures.

Information
[0xA04 
(2564)]

A known failed path is 
now functional and 
passed retest.

No action necessary.

StorView Server Event 

Messages

Type [ID]

Cause

Action

Summary of Contents for E-842R





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands