Gateway 930 series System Manual Download

Page: 121 / 160

Diskette drive problems

113

Diskette drive problems

The system does not recognize the diskette drive.

The diskette drive will not read, write, or format.

The diskette drive LED illuminates continuously.

Probable cause

Solution

The diskette drive may be
configured incorrectly

Restart your server, then press

to open the

BIOS Setup utility. In the Advanced | Floppy
Configuration menu, make sure that the
diskette drive parameters are set correctly.

The drive cables are not
connected properly

Open the system and make sure all cables are
correctly connected to the system board.

Probable cause

Solution

The diskette is not IBM
formatted

Make sure the diskette you are trying to format
is IBM compatible. If it is, try reformatting it. If
it is not, get a compatible diskette.

The diskette is corrupted

Run Check Disk on the diskette. If errors are
detected and corrected, try accessing the
diskette again.

The diskette is
write-protected

Make sure the write-protection window on the
upper-right corner of the diskette is closed
(unprotected).

Probable cause

Solution

The diskette is corrupted

Remove the diskette from the drive. If the light
remains on, try restarting the system.

The cable to the drive is not
connected properly

Open the system and make sure the cable is
connected properly between the diskette drive
and its controller. Make sure the pins are not
bent or misaligned.

8508088.book Page 113 Thursday, November 1, 2001 9:35 AM

Summary of Contents for 930 series

































































































































































Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands

Gateway 930 series, System Manual

Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands