manualshive.com logo in svg

Gateway 930 series, System Manual, Page: 120 / 160

Share
Download
Gateway 930 series System Manual Download Page 120

112

Troubleshooting

The system does not recognize the CD drive.

Probable cause

Solution

The CD is not intended for PC
use

Make sure the CD is PC compatible.

The CD is loaded incorrectly

Make sure the label is facing up, then try again.

The CD is scratched or dirty

Try cleaning the CD with a lint-free cloth. Make
sure the CD is not scratched.

The CD drive needs to be
added as new hardware

In the Control Panel window (Start | Settings |
Control Panel), double-click Add New
Hardware. Follow the on-screen instructions
for adding the drive.

The secondary IDE device
may be disabled

Restart your server, then press

F1

to open the

BIOS Setup utility. From the Advanced | IDE
Configuration menu, set the IDE Controller
to Both and the Secondary IDE Master to
Auto.

The CD cables are not
installed correctly

Open the system and make sure all cables
between the CD controller and the CD drive
are connected correctly.

The CD drive may be
defective

Replace the CD drive.

8508088.book Page 112 Thursday, November 1, 2001 9:35 AM

Summary of Contents for 930 series

































































































































































Reviews:

No comments