Gateway 930 series System Manual Download | Manualshive

Page: 109 / 160

background image

System administration and control

101

10

Remove the Windows 2000 Server operating system CD, then insert the
SCCD. Close the browser if it opens automatically.

11

Click

Start

, then select

Settings

, then

Control Panel

.

12

Double-click the

Add/Remove Hardware

icon.

13

In the Add/Remove Hardware Wizard dialog box, click

Next

.

14

Click

Add/Troubleshoot a device

, then click

Next

.

15

Click

Add a new device

, then click

Next

.

16

Click

No, I want to select the hardware from a list

, then click

Next

.

17

Click

Other devices

, then click

Next

.

18

Click

Have disk

.

19

In the Install From Disk dialog box, type:

d:\drivutil\mngmt_sw\mgagent\gw_930\2kdriver

(where d is the

drive letter of your CD drive).

20

Click

OK

. The

Gateway 930 Series Driver

appears in the Models box.

21

Click

Next

. The Gateway 930 Series driver is ready for installation.

22

Click

Next

. The wizard installs the driver.

23

Click

Finish

.

To install the ManageX Event Manager:

The following instructions refer to installing the ManageX Event Manager
through either Internet Explorer or Netscape navigator. Only one computer
on the network must have ManageX. You will use this computer to manage
all of the nodes on the network.

1

Insert the Server Companion CD (SCCD) into the CD drive. In the
browser, click the Gateway

930

tab.

2

In the left frame, click

ManageX Event Manager

under the heading

Manageability Software

.

8508088.book Page 101 Thursday, November 1, 2001 9:35 AM

«
...
107
108
109
110
111
...
»

Summary of Contents for 930 series

































































































































































Reviews:

No comments

Related manuals for 930 series

BladeCenter HS22

Brand: IBM Pages: 18

88631SU - System x3850 - 8863

Brand: IBM Pages: 90

Brand: TYAN Pages: 170

Modbus Server-FC330A

Brand: IntesisBox Pages: 5

Brand: Gigabyte Pages: 115

Brand: Jatheon Pages: 52

Brand: ACTi Pages: 11

Brand: Nortel Pages: 144

Brand: Data-Tronix Pages: 29

Brand: Data-Tronix Pages: 30

Brand: Intel Pages: 69

MFSYS25 - AXXPSU 1000W Power Supply Module

Brand: Intel Pages: 164

Brand: Intel Pages: 226

Brand: XtendLan Pages: 28

Brand: Kramer Pages: 28

Brand: TRENDnet Pages: 2

Brand: TRENDnet Pages: 2

TEW-P1UG - Wireless Print Server

Brand: TRENDnet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands